Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Thrust
51118
51118 is a thrust designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 90 × 120 × 22 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
None. PLB’s table gives the size, 90 × 120 × 22 mm, and a mass of 0.656 kg, and nothing else. SKF prints C 59.2 kN and C0 208 kN for its own 51118, but that rating belongs to SKF’s bearing, not to PLB’s. Ask PLB for the axial ratings of the part it will ship.
The two masses differ by 14 g, which says nothing about whether the internal designs match. Because PLB publishes no rating, an axial life calculation for a PLB bearing has to start from a figure PLB gives you in writing.
PLB heads the height column B; SKF calls the same dimension H. Both are the overall height of the assembled bearing.
The two washers are not the same part.
A single-direction thrust ball bearing has a shaft washer, a housing washer and a ball-and-cage set. The shaft washer has the smaller bore and sits on the shaft; the housing washer has a larger bore and is supported in the housing. Fitting them the wrong way round lets the housing washer rub on the shaft.
PLB’s table gives only the overall d, D and height. It does not give the housing-washer bore, the shaft-washer outside diameter or the chamfers. Ask PLB for the drawing with those dimensions before you machine the shaft and housing seats.
The bearing carries axial load in one direction only. If the load reverses, or there is a radial load, ask PLB whether 51118 suits the duty at all; a double-direction or different bearing type may be needed.
PLB’s IATF 16949 certificate does not cover thrust bearings.
The row comes from 慈溪灵帆轴承有限公司 (CIXI LingFan Bearing Co., Ltd., brand PLB), No. 1018 Kaifa Road, Zhouxiang Town, Cixi, Zhejiang. Its company page says it was founded in 1992 under the earlier name 杭州湾轴承 (Hangzhou Bay Bearing). [3][4]
PLB shows an IATF 16949:2016 certificate from NQA, certificate T10938 (IATF 0550115), valid from 15 October 2024 to 14 October 2027. Its scope is the production of deep groove ball bearings with a bore of 2.5–40 mm, excluding product design. [5] A 51118 thrust bearing with a 90 mm bore is outside that scope. The ISO 14001 certificate shown on the same page also names deep groove ball bearing production.
So ask PLB where the 51118 is made and which quality certificate covers that product. The certificate on the site is not evidence for this bearing.
What each manufacturer published.
Manufacturer
Reference mass (kg)
Source recorded
PLB 51118 PLB’s single-direction thrust ball bearing table prints only four columns for 51118: d 90, D 120, B 22 (尺寸 mm) and 0.656 (重量 kg). It prints no load rating, speed or washer dimensions.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
15 mm
Mean diameter dm
(D + d) / 2
105 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
PLB connects a searchable miniature/automotive catalogue with named inspection equipment and ring/assembly process steps. Specify closure-dependent widths, keep alternator reference numbers separate from the delivered construction, and request part-linked test conditions for custom robot or rail-component work.
Published ranges: Automotive alternator and steering bearings · Motor bearings · Precision spindle-bearing applications · Nonstandard bearing designs
124 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Redirects to /product/DataTables/57 (单向推力球轴承). 51118 row from the table’s own data request: 型号 51118, 尺寸(mm) d 90, D 120, B 22, 重量kg 0.656. No other columns. Read 2026-10-30.
IATF 16949:2016, NQA T10938 / IATF 0550115, 15 Oct 2024 – 14 Oct 2027, scope 内径 2.5mm-40mm 深沟球轴承的生产 (删减产品设计); ISO 14001 scope 深沟球轴承的生产. Read from the certificate images 2026-10-30.
Guide checked 2026-10-30. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies