BearingIndex
THE BEARINGINDEX DIRECTORY

5200 — 10 × 30 × 14.3 mm

BOUNDARY DIMENSIONSUNIT / mm

TSB labels this publication “Double Row Series Deep Groove Ball Bearing” and its series sketch uses width W. The 5200 row gives 10/30/14.3 mm; its open and shields/seals width entries are both 14.3 mm. A generic single-row d/D/B sketch would not establish the offered double-row construction.

Deep groove ball

5200

5200 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 10 × 30 × 14.3 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
10 mm
Outside D
30 mm
Width B
14.3 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 10×30×14.3 mm request still needs the brand, closure and actual double-row construction.

TSB publishes 5200 with the same 14.3 mm width in its open and shields/seals columns. Its page calls the range double-row deep-groove, while NSK publishes a same-size 5200 as double-row angular-contact. TSB’s diameter tolerance columns are in micrometres and its dynamic-load entry is 1.996 under a KN heading. Keep these source-specific details attached to the offered part.

14.3 mm in both width columns does not choose the supplied closure.

TSB’s exact 5200 row [1] lists bore 10 mm, outside diameter 30 mm, OPEN width 14.3 mm and SHIELDS SEALS width 14.3 mm. The row carries only the base designation 5200; it does not itemise a separate complete designation for each closure.

TSB publication [1]What is actually shownResolve on the offer
5200 width columns14.3 / 14.3 mmWhich construction is supplied? Equal nominal width does not distinguish open, shielded or sealed.
Series sketchesOpen; one shield Z; two shields ZZ; snap ring NR.Ask for the exact offered suffix and drawing. Series pictures do not confirm availability of every illustrated form for 5200.
Dimension symbolW on the series sketch; width in the table.This directory’s stored B 14.3 mm refers to that width entry. Keep the source drawing’s W label on the technical request.

If the request says only “5200, 10×30×14.3”, TSB’s table cannot decide whether the buyer expects open or closed supply. State the closure and lubrication scope explicitly, then have the quotation identify the complete part and delivered state. The combined shields/seals column supplies no seal compound, contact arrangement or grease specification.

If a snap-ring form is proposed, request its selected drawing and retention interface. The NR family sketch is not a 5200 groove-dimension release. Likewise, equal listed width does not establish equal running resistance, permissible speed or mounting details across the illustrated constructions. Obtain those details for the offered configuration rather than deriving them from 14.3 mm.

Keep the μm columns and the brand-specific load figure attached to TSB 5200.

The TSB table separates nominal diameters in mm from their adjacent tolerance columns in μm. Read the two-level headers before copying its row into a drawing or inspection sheet.

Exact TSB 5200 field [1]Published entryBoundary of this evidence
I.D / adjacent Tol.10 mm / 0/−8 μmA bore-related catalogue entry; request the drawing’s measurement definition and applicable tolerance conditions.
O.D / adjacent Tol.30 mm / 0/−9 μmDo not move this tolerance to width or confuse micrometres with millimetres.
Basic dynamic load1.996 under “BASIC DYNAMIC LOAD-KN”.Retain the published label and ask TSB to confirm its basis for the selected construction.

The diameter entries are not shaft or housing fit prescriptions. This page does not provide a width tolerance, full accuracy-class definition or measurement procedure for the delivered part. Specify the mating interfaces through the responsible design process and obtain the supplier’s controlled inspection requirements.

The same number can identify a separately described product. NSK’s 5200 publication [2] calls its product double-row angular-contact, with 10/30/14.3 mm dimensions and basic dynamic load Cr 7850 N. TSB’s page calls its range double-row deep-groove and prints 1.996 under KN. Those are two brands’ statements, not a common rating or proven interchange.

Do not correct TSB’s value to NSK’s rating, infer a contact angle from the series number, or approve a cross-brand replacement from the three matching dimensions. Ask TSB to identify its internal construction, explain the applicable load rating and provide the selected drawing. If the design requires a particular radial/axial duty or angular-contact arrangement, put that requirement into the technical review explicitly.

An acceptable response ties the offered TSB designation and closure to its own dimensions, tolerance definitions and load assessment. A quote that borrows NSK’s data while supplying an unidentified TSB 5200 still leaves the procurement question unresolved.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Recorded width; source W (mm)Source recorded
TSB
5200
103014.32026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish 5200.

TSB

Ningbo, Zhejiang, China

Standard and custom ball and roller bearings

TSB publishes both bearing families and equipment-component routes. Its 502-0113 mower assembly specifies a particular 6203-based variant, while older factory and JIT pages need current confirmation; buyers should qualify the assembly, plant and delivery programme separately.

Published ranges: Standard and custom ball bearings · Cylindrical roller bearings · Tapered roller bearings · Custom bearing and seal arrangements

18 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask TSB about 5200

Request a quote for 5200.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. TSB · 5200 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. TSB · Double Row Series exact 5200 table and sketches ↗

    Two-level headers and the 5200 row: 10/30 mm, I.D 0/−8 μm, O.D 0/−9 μm, open and shields/seals widths both 14.3 mm, basic dynamic load 1.996 under KN. Page labels double-row deep-groove; series sketches identify W, Z/ZZ/NR but do not release each delivered configuration.

  2. NSK · separately branded 5200 double-row angular-contact publication ↗

    NSK 5200: double-row angular-contact, 10/30/14.3 mm and Cr 7850 N. Used to show that a same-name/size comparison cannot transfer construction or ratings to TSB; no interchange approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.