BearingIndex
THE BEARINGINDEX DIRECTORY

TSB

TSB Bearing Group: bearings, mower assemblies and pulleys, with a guide to matching parts and defining the supplying entity and replenishment programme.

TSB · BEARINGS & EQUIPMENT COMPONENTS

Separate the bearing, the equipment assembly and the supply programme.

TSB describes ball/roller bearings, wind-generator bearings, iron/aluminium castings and stamped or split steel pulleys. Group introduction [1] A catalogue bearing request, a mower-spindle assembly and a recurring overseas replenishment programme involve different matching and acceptance. Identify the actual deliverable before treating this broad portfolio as one factory’s interchangeable output.

Prepare a sourcing inquiry
01

502-0113 shows why an assembly reference matters more than a base bearing number.

TSB’s 502-0113 page describes a spindle/jackshaft housing assembly with Murray 1001200 and MTD 1001046 replacement references, a shaft with grease fitting and nut, nut reference 210-0003, and bearing reference 200-1031 described as “6203 Z-0.669 Bore”. [2] These are the manufacturer’s published references, not a BearingIndex-verified fitment or a current parts-availability promise.

For an assembled replacement

Send the equipment’s exact model, serial/year information, original part reference and installation drawing or measured interfaces. Ask TSB to confirm the offered assembly revision, mounting geometry, shaft and fastening arrangement, included parts and any exclusions. The page’s broad “2001 models and up” wording is not enough to approve every later machine.

The pulley catalogue also lists distinct part codes. The reviewed 700-0112 detail names the part but supplies no readable numerical geometry or belt specification. [3] Request groove/profile, mounting, material and assembly requirements for that offered part; the code alone cannot establish interchangeability.

02

The angular-contact table provides a useful, limited selection example.

The official table gives 7004□ dimensions of 20 × 42 × 12 mm for bore, outside diameter and width, and maps its placeholder to contact-angle suffixes: C at 15°, AC at 25° and B at 40°. [4] This is one published table entry, not proof that every suffix is currently in stock or interchangeable in your assembly.

Complete the designation

Confirm the required contact-angle suffix, applicable accuracy, cage and lubrication with a part-specific drawing. Include radial/axial load directions, speed and mounting conditions. A dimension match alone does not choose the contact angle.

Define the arrangement

If the project uses a pair or another arrangement, specify orientation, matching and preload/clearance acceptance. Request the supplier’s offered configuration and test evidence; the basic dimension table does not itself establish those order requirements.

03

A dated JIT offer needs a current operating agreement.

TSB’s delivery article is dated 12 May 2016. It describes just-in-time delivery, a safety-stock programme, an expected two-month supply in a US warehouse, and customer-specific packaging/labels. [5] Its USA contact page separately identifies a Wisconsin office and engineering/customer-support routes. [6] These publications do not confirm today’s inventory, programme eligibility or response time.

  1. Define the part and forecast. Agree the approved configuration, expected usage, forecast horizon and how changes will be communicated.
  2. Define the stock responsibility. Confirm current warehouse, supplier entity, ownership of buffer inventory, replenishment rules and responsibility for obsolete or changed parts.
  3. Define each release. Agree order/release quantities, delivery location, lead-time commitments, packaging and labels. Obtain a dated quotation and contract rather than relying on an old website paragraph.
04

Do not join historical plant pages into one current capability claim.

The website’s Shaoxing factory entry, published in April 2016, states a 15–30 mm primary bore range but also lists wider bearing-series spans. It records an ISO 9002 certification dated May 2001. [7] The text does not reconcile those ranges or establish a current certified scope. Ask which plant makes your exact item and what present range and qualification apply.

The similarly dated ZVL Auto entry is a separate European record with its own ZVL mark and old VDA/ISO/TS wording. [8] Its historical dimensions, staffing or certificates must not be assigned to a Ningbo or Shaoxing bearing order. Its appearance under friendly links also does not establish current ownership or supply responsibility.

The May 2016 quality page separates “TSB Group Certifications” and “ZVL-Auto Certifications” and describes internationally sourced materials/grease. [9] Request the complete current certificates for the contracting entity/site and the actual material/lubricant record for the quoted part. Homepage inspection or standards language does not replace a lot report.

The main contact page names 天胜轴承集团有限公司 at No. 18 Yongjiang South Road, Beilun, Ningbo. [10] A government-hosted 2022 Beilun industrial enterprise land-efficiency evaluation also contains that exact Chinese entity. [11] This corroborates a historical entity record in that district; its evaluation category is unrelated to bearing quality or project approval.

YOUR NEXT STEP

Prepare a TSB part-and-programme inquiry.

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

18 model records
Model / bearing familyManufacturerBore dOutside DWidth B / T / LDetails

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Manufacturer publicationTSB · group introduction ↗

    Broad bearing/casting/pulley and application positioning; does not allocate all production to one plant.

  2. Manufacturer part pageTSB · mower assembly 502-0113 ↗

    Published replacement and component references; fitment, current revision and availability not independently verified.

  3. Manufacturer part pageTSB · pulley 700-0112 ↗

    Part identity; no readable numerical geometry/belt specification obtained.

  4. Manufacturer catalogue tableTSB · angular-contact table ↗

    Explicit mm dimensions and angle/suffix mapping; not arrangement qualification or current stock.

  5. Historical manufacturer programme descriptionTSB · just-in-time delivery, 12 May 2016 ↗

    Dated buffer-stock, packaging and US warehouse description; current programme terms need agreement.

  6. Manufacturer contact pageTSB · USA office ↗

    Wisconsin office/support routes; not proof of available stock or current contracted service level.

  7. Historical manufacturer site descriptionTSB · Shaoxing factory, 30 April 2016 ↗

    Unreconciled primary size/series text and old ISO 9002 wording; no current factory qualification inferred.

  8. Historical manufacturer-linked entryTSB · ZVL Auto entry, 30 April 2016 ↗

    Separate European entity/brand and old certificate wording; current ownership and Chinese-order responsibility not established.

  9. Historical manufacturer quality publicationTSB · materials and quality, 12 May 2016 ↗

    Distinct group/ZVL certificate headings and sourcing description; actual current site/part records required.

  10. Manufacturer identity/contact publicationTSB · main contact page ↗

    Chinese entity and Beilun contact address; not a complete current plant or export-entity map.

  11. Historical government enterprise recordBeilun · 2022 industrial enterprise land-efficiency evaluation ↗

    Exact Chinese group name in a dated district evaluation; unrelated to bearing quality, certification or programme approval.

Report a source correction → · Return to inquiry checklist ↑

TSB published product scope reviewed

The manufacturer website describes standard and custom ball and roller bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:34

Source documentation retained for editorial review.