BOUNDARY SIZE AND CORNER GEOMETRY ARE DIFFERENTUNIT / mm
55 × 100 × 21 mm is the shared boundary size. Use the selected manufacturer’s corner and shoulder drawing to review the bearing-seat interface; the directory size is not that drawing.
Deep groove ball
6211
6211 is a deep groove ball designation documented on BearingIndex from 2 manufacturer publications. HCH and ZYS both publish d55/D100/B21 mm and a minimum bearing chamfer of 1.5 mm. That minimum does not describe the complete corner shape or the mating shaft radius. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
What does the 1.5 mm chamfer entry actually tell a 6211 buyer?
It gives a minimum corner dimension, not a fixed 1.5 mm radius. SKF uses 6211 itself to demonstrate different radial and axial maxima. HCH separately publishes its shoulder diameters; keep both types of dimension on the right component.
The manufacturer’s 6211 example has two different maximum dimensions.
SKF’s own worked example [3] starts with 6211 bore d = 55 mm and minimum chamfer r1,2 = 1.5 mm. Its Table 15 gives:
Dimension in the SKF example
Value
Radial chamfer maximum r1
2.3 mm
Axial chamfer maximum r2
4 mm
The diagram measures along two directions. These limits do not specify a circular 1.5 mm radius or a 45° bevel. An incoming check needs the radial and axial dimensions, not a single assumed radius.
The 4 mm number belongs to the bearing, not the shaft.
SKF’s separate ordinary 6211 mounting row gives mating fillet ra maximum 1.5 mm. The 4 mm axial chamfer maximum is not permission to machine a 4 mm shaft fillet. These are SKF dimensions; neither HCH nor ZYS inherits them from the shared designation.
For the offered bearing, put its corner limits on the component inspection drawing. Put the mating fillet and locating shoulders on the assembly drawing. This separates incoming bearing geometry from the fit of the assembled parts.
HCH provides a shoulder range as well as the 55 mm bore.
HCH’s exact 6211 row and mounting diagram [1] identify shaft-shoulder da and housing-shoulder Da. The millimetre columns give da minimum 62, maximum 67; Da maximum 92. Those are shoulder diameters, separate from bore d55 and outside D100.
Use the complete 62–67 mm range when reviewing a selected HCH interface. A check that records only “shoulder at least 62” loses the published upper bound. The same row’s bearing r minimum 1.5 mm supplies neither a mating fillet maximum nor a complete corner profile.
The quoted item must stay with its own drawing. A shoulder range read from HCH is not a new specification for a ZYS offer. ZYS’s exact 6211 row [2] publishes rs minimum 1.5 mm and lists closure and snap-ring variants, but its examined table does not supply HCH’s shoulder range. Its column D2 maximum 106.5 is not labelled Da; do not use it as the housing-shoulder limit.
What the drawing review should return
Return a selected manufacturer’s bearing drawing with both corner directions identified, plus the assembly drawing locating the two rings. For HCH, show the actual da against both 62 and 67 and Da against 92. Resolve the mating fillet from that maker’s mounting requirements before releasing the assembly drawing. The source row settles these dimensional questions; it does not establish fit tolerances, operating clearance or current availability.
What each manufacturer published.
Manufacturer
Bore (mm)
Outside diameter (mm)
Width (mm)
Source recorded
HCH 6211 Original record retains dimensions only. Current HCH source: r min1.5 mm; shaft shoulder da min62/max67 and housing shoulder Da max92 mm. Approximate mass0.6060 kg. Cr39.070/Cor26.540 have conflicting lbs/KN headings; speed headings also conflict. No unit or multiplier guessed.
ZYS 6211 Original record retains dimensions only. Current ZYS 6211 row: rs min1.5, Cr43.4/Cor29.2 kN, mass0.607 kg. D2max106.5 is not labelled a housing-shoulder Da. Closure and snap-ring columns describe variants, not confirmed availability.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.
Compare the recorded figures.
Property
Finding
Sources
Bore
All 2 sources publish 55 mm
2
Outside diameter
All 2 sources publish 100 mm
2
Width
All 2 sources publish 21 mm
2
Where the figures differ, use the drawing from the manufacturer you buy from.
HCH publishes metric and inch ball bearings, tapered roller bearings and steel balls. Review the product route, production documents and export-entity evidence before sourcing.
23 designations documented here · source recorded 2026-10-08
ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.
87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Exact 6211 row, paired mm/inch headers and original da/Da drawing read. da min62/max67, Da max92 mm. Other Parameters has conflicting parent/subcolumn load and speed unit headings; not resolved by guessing.
6211 d55/D100/B21, rsmin1.5; Cr43.4/Cor29.2 kN and mass0.607 kg. PDF continuation page3 matches. D2max106.5 is not labelled a housing-shoulder Da. Series photos are not identified as6211.
17000, printed37/PDF39 actual6211 example and corner figure; printed53/PDF55 Table15; printed280–281/PDF282–283 aligned ordinary6211 row and mating fillet. SKF only, not either directory manufacturer’s specification.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies