BearingIndex
THE BEARINGINDEX DIRECTORY

6410 — 50 × 130 × 31 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 31 mmD = 130 mmd = 50 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

6410

6410 is a deep groove ball designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 50 × 130 × 31 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
50 mm
Outside D
130 mm
Width B
31 mm

Compare the 2 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-08

Your old 6410 uses an outer-ring retaining groove. What should you order?

LYC lists a plain 6410 separately from 6410 EN and 6410 E-ZN groove variants. All have a 50 × 130 × 31 mm envelope. That envelope cannot tell the buyer whether the locating groove needed by the old housing is present.

Start with the housing’s locating method, not the bare number.

Read the complete old marking and inspect the housing drawing for the feature that locates the outer ring. If a retaining ring engages an outer-ring groove, the replacement requirement includes that groove. Do not delete the suffix when preparing the order.

LYC’s plain 6410 row [1] supplies the 50/130/31 mm envelope but does not make the grooved rows interchangeable with it. The groove section [2] names 6410 EN and 6410 E-ZN separately. The selected construction and its groove drawing must appear on the quote; a bare 6410 quote leaves the locating feature unresolved.

This is a drawing-selection question, not a recommendation to modify the bearing or cut a groove. If the supplier proposes a different locating method, it changes the assembly and needs a revised mounting design.

Use the groove dimensions only for the named groove variants.

For LYC’s 6410 EN / 6410 E-ZN entries, the examined catalogue gives Dn = 125.22 mm, a = 4.06 mm, b = 3.1 mm and r1s minimum = 0.6 mm. Compare these symbols with the catalogue diagram and the housing’s required ring position; do not reinterpret them as shaft or shoulder dimensions.

Request the controlled drawing with groove tolerances and the specified matching retaining component. The nominal catalogue fields alone do not qualify a ring from the old assembly. Confirm what the quoted suffix includes rather than assuming a ring is supplied.

Keep the rest of the selected row attached to it. The groove rows publish C/C0 = 92/55 kN, grease/oil speeds 5300/6300 r/min and 1.91 kg. The plain row gives 92.5/55.2 kN, 5100/6100 r/min and 1.87 kg. Do not quote the plain row’s ratings together with the groove row’s speed to create a combined specification.

If the drawing uses a shoulder, distinguish the two radius symbols.

The LYC mounting fields for these examined rows include da minimum 61 mm, Da maximum 119 mm and ra maximum 2 mm. The bearing’s minimum corner-radius field is 2.1 mm. A 2.1 mm bearing edge field is not permission to specify a 2.1 mm mating shoulder fillet.

Use the mounting diagram to identify which shoulder each symbol describes, then check the actual shaft/housing drawing. These catalogue bounds support that interface check; they do not define fits, clearance or permissible housing loads. If the old drawing’s corner exceeds the listed ra bound, obtain a reviewed mounting solution rather than changing the published number.

This is evidence from a published catalogue, not a current supply promise.

The LYC PDF is an existing manufacturer publication. Confirm the selected suffix and current controlled drawing with LYC before finalising the replacement. INYOUNG’s historical source [3] showed a maintenance message on 2026-10-08, so its current 6410 row could not be rechecked. Historical directory figures are not newly verified in this guide and cannot establish an alternative groove construction.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Minimum corner radius (mm)Reference mass (kg)Source recorded
LYC
6410
92.555.2510061002.11.872026-10-01 source ↗Request
INYOUNG
6410
92.355.252006400—1.862026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingRanges 92.3 – 92.5 kN across 2 sources2
Static load ratingAll 2 sources publish 55.2 kN2
Limiting speed — greaseRanges 5100 – 5200 rpm across 2 sources2
Limiting speed — oilRanges 6100 – 6400 rpm across 2 sources2
Reference massRanges 1.86 – 1.87 kg across 2 sources2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 240 mm
Mean diameter dm(D + d) / 290 mm
C / C₀ load ratio (2 sources)dynamic ÷ static load ratingLYC 1.68 · INYOUNG 1.67

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 6410.

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 6410

LYC

Ball and roller bearings

LYC publishes a broad bearing portfolio. This sourcing guide separates catalogue selection, engineered applications and order-specific evidence.

49 designations documented here · source recorded 2026-10-07

Ask LYC about 6410

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
GeneratorsINYOUNG
MotorcyclesINYOUNG

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
640420 × 72 × 19Deep groove ball1
640735 × 100 × 25Deep groove ball1
640840 × 110 × 27Deep groove ball2
640945 × 120 × 29Deep groove ball2
641575 × 190 × 45Deep groove ball1
641680 × 200 × 48Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 6410.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. LYC · 6410 source ↗

    Directory record dated 2026-10-01. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. INYOUNG · 6410 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. LYC · deep-groove catalogue, plain 6410 row ↗

    PDF page 5, printed pages 105–106: exact 6410 dimensions, ratings, speeds, mass, mounting symbols and diagram. Current quotation/drawing to be confirmed.

  2. LYC · same catalogue, snap-ring-groove rows ↗

    PDF page 14, printed pages 123–124: 6410 EN and 6410 E-ZN and their groove dimensions. These figures are not assigned to the bare designation.

  3. INYOUNG · historical 64-series source currently in maintenance ↗

    2026-10-08 actual page says the site is under maintenance. No current 6410 row could be read; historical directory data are not reverified here.

Guide checked 2026-10-08. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.