BearingIndex
THE BEARINGINDEX DIRECTORY

6907 — 35 × 55 × 10 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 10 mmD = 55 mmd = 35 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

6907

6907 is a deep groove ball designation documented on BearingIndex from 3 manufacturer publications. The published boundary dimensions are 35 × 55 × 10 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
35 mm
Outside D
55 mm
Width B
10 mm

Compare the 3 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-08

Do the 6907 catalogue speeds qualify a sealed bearing at 9,000 r/min?

Not by themselves. In this example, 9,000 r/min is a proposed operating speed, not a tested result. NBK explicitly labels its speed columns non-contact; RCL gives grease/oil values without resolving the closure of the quoted item. Identify that construction before treating either number as approval.

NBK’s 10,000 grease entry has a condition attached.

NBK’s actual 6907 row [2] lists 35/55/10 mm and grease/oil speeds of 10,000/13,000 r/min. Both column headings say non-contact. The proposed 9,000 r/min is numerically below the grease entry, but that comparison has not identified the seal construction.

If the offer uses a contacting seal, ask NBK for the speed limit and duty assessment for that full designation. Its non-contact heading cannot be rewritten as an approval for a contact-sealed item. If the offered construction does match the stated condition, the actual lubricant, loads and operating temperature still need to be included in the assessment.

A catalogue row ending at the bare 6907 code leaves the exact closure unresolved. Get the complete suffix and closure description on the quote before selecting it for the proposed sealed application.

RCL’s higher entry does not settle the closure question either.

RCL publishes 12,000/15,000 r/min [1] for grease/oil in its 6907 row. Its dynamic/static figures are 10370/7190 N; NBK gives 10370/7180 in its load columns. Those almost matching ratings do not establish identical seal friction or speed capability for two quoted sealed versions.

Ask RCL which complete designation, closure and lubrication configuration its 12,000 entry covers. Provide the proposed 9,000 r/min duty and the load/temperature requirement, and request a response tied to that item. ‘Our table says 12,000’ would still leave the configuration unanswered.

For a replacement in an existing 35 mm-shaft assembly, preserve the old seal requirement and drawing. The shared 35/55/10 envelope is useful for dimensional screening, but it does not justify changing a seal to obtain a higher catalogue speed.

A speed answer is not a relubrication or grease-life answer.

If the chosen bearing is lubricated for life, ask for the expected grease-life basis at the actual bearing temperature and duty. SKF’s published grease-life discussion [4] treats size, speed, temperature and operating conditions as inputs. It does not provide a life result for either RCL or NBK 6907.

Keep the grease-life question separate from fatigue-life selection: obtain the actual grease specification and configuration first, then the applicable life assessment. This page has no measured bearing temperature, operating load or test duration, so it cannot promise hours of operation or assign a replacement interval to the proposed 9,000 r/min example.

The selection is ready for review when the supplier has identified the full sealed item and answered its speed and grease-duty requirements. Until then, the two catalogue numbers are screening evidence, not a supplier ranking or application approval.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Sihai
6907
—————2026-09-24 source ↗Request
RCL
6907
10.377.1912000150000.0752026-09-24 source ↗Request
NBK
6907
10.377.181000013000—2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingAll 2 sources publish 10.37 kN2
Static load ratingRanges 7.18 – 7.19 kN across 2 sources2
Limiting speed — greaseRanges 10000 – 12000 rpm across 2 sources2
Limiting speed — oilRanges 13000 – 15000 rpm across 2 sources2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 210 mm
Mean diameter dm(D + d) / 245 mm
C / C₀ load ratio (2 sources)dynamic ÷ static load ratingRCL 1.44 · NBK 1.44

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 6907.

NBK

Ningbo, Zhejiang, China

Deep groove ball bearings and custom variants

NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.

Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings

32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask NBK about 6907

RCL

Ningbo, Zhejiang, China

Thin-wall ball bearings for compact mechanisms

RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.

Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings

131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask RCL about 6907

Sihai

Ningbo, Zhejiang, China

Deep groove bearings for motors and automotive use

Sihai publishes a separate automotive table with wider 63001 and 62201 references, plus high-temperature generator grease, C3 and seal-material statements. Compare the actual section and complete offered build rather than replacing these with similar ordinary catalogue numbers. Its displayed IATF document covers miniature deep-groove manufacture with product design excluded; request current verified status and a part-specific automotive approval package.

Published ranges: 6000, 6200 and 6300 series · 6800 and 6900 series · Automotive engine-bearing applications

85 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Sihai about 6907

Applications the publishing works state.

ApplicationStated by
Automotive systemsSihai
BicyclesRCL
Circular loomsRCL
Encoders and motorsRCL
Household appliancesSihai
Office equipmentSihai
Power toolsSihai
RoboticsRCL

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 35x55x10 mm envelope.

DesignationBearing familyWorks
61907Deep groove ball2
6907ZZ/2RSDeep groove ball1
71907Angular contact1
H71907-AC-TA-HQ1-P4Angular contact1
H71907-AC-TA-P4Angular contact1
H71907-C-TA-2RZ-HQ1-P4Angular contact1
H71907-C-TA-HQ1-P4Angular contact1
H71907-C-TA-P4Angular contact1
S6907ZZ/2RSDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
690010 × 22 × 6Deep groove ball7
6900zz10 × 22 × 6Deep groove ball1
6900ZZ/2RS10 × 22 × 6Deep groove ball1
690112 × 24 × 6Deep groove ball6
6901zz12 × 24 × 6Deep groove ball1
6901ZZ/2RS12 × 24 × 6Deep groove ball1
690215 × 28 × 7Deep groove ball5
6902ZZ/2RS15 × 28 × 7Deep groove ball1
690317 × 30 × 7Deep groove ball5
6903ZZ/2RS17 × 30 × 7Deep groove ball1
690420 × 37 × 9Deep groove ball5
6904ZZ/2RS20 × 37 × 9Deep groove ball1
690525 × 42 × 9Deep groove ball5
6905ZZ/2RS25 × 42 × 9Deep groove ball1
690630 × 47 × 9Deep groove ball5
6906ZZ/2RS30 × 47 × 9Deep groove ball1
6907ZZ/2RS35 × 55 × 10Deep groove ball1
690840 × 62 × 12Deep groove ball3

Each envelope shown is that designation’s own published size.

Request a quote for 6907.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Sihai · 6907 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. RCL · 6907 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  3. NBK · 6907 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. RCL · 69-series actual manufacturer table ↗

    6907 row, N and g headings, grease/oil speed columns; selected quoted configuration remains to be confirmed.

  2. NBK · 6900-series actual manufacturer table ↗

    6907 dimensions and ratings; non-contact speed headings. No supplier ranking or application approval.

  3. SKF · Bearing Installation and Maintenance Guide ↗

    Printed pages 3 and 11–12: construction and selection/mounting factors. Technical background, not specifications for RCL or NBK.

  4. SKF Evolution · grease life in lubricated-for-life deep-groove bearings ↗

    Published model inputs and conditional grease-life discussion; no current product or lifetime guarantee applied here.

Guide checked 2026-10-08. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.