BearingIndex
THE BEARINGINDEX DIRECTORY

MR126 — 6 × 12 × 4 mm

A 4 MM WIDTH DOES NOT IDENTIFY THE CLOSUREUNIT / mm

RCL lists MR126 at 6 × 12 × 4 mm without a closure column. EZO lists MR126 at 3 mm wide, and MR126ZZ / MR126 2RS at 4 mm wide. NSK’s MR126ZZMC3 is also 4 mm wide. Their ratings and speed entries differ.

Deep groove ball

MR126

MR126 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. This 6 × 12 × 4 mm directory row is RCL’s publication. EZO’s open MR126 is 3 mm wide, while its ZZ and 2RS rows and NSK’s MR126ZZMC3 are 4 mm wide. Read the complete designation alongside the speed limits. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
6 mm
Outside D
12 mm
Width B
4 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-11-04

MR126ZZ and MR126 2RS share a 4 mm width, but EZO lists different speeds.

EZO lists both closed versions at 6 × 12 × 4 mm and 716 N dynamic rating. Its ZZ row gives 50,000 min⁻¹ with grease; its 2RS row gives 39,000. RCL’s 4 mm MR126 row and NSK’s MR126ZZMC3 carry their own figures. Choose the complete configuration before using a speed or load value.

Three makers, five precisely identified rows.

A gloved hand presents a miniature bearing beside a compact motor end housing
Illustrative miniature-bearing installation; no particular factory or maker is depicted.
Maker / published designationBore × OD × width, mmDynamic / static rating, NGrease / oil speed, min⁻¹Reference mass
RCL MR126 [1]6 × 12 × 4716 / 29043,000 / 50,0001.66 g
NSK MR126ZZMC3 [2]6 × 12 × 4790 / 29243,000 / not listed0.00174 kg
EZO MR126 [3]6 × 12 × 3716 / 29350,000 / 59,0001.23 g
EZO MR126ZZ [4]6 × 12 × 4716 / 29350,000 / 59,0001.57 g
EZO MR126 2RS [5]6 × 12 × 4716 / 29339,000 / 39,0001.62 g

Checked on 4 November 2026. RCL labels its speeds r/min, the other sources min⁻¹; the table uses revolutions per minute. The directory’s RCL values in kN and kg are arithmetic conversions: 716 N ÷ 1,000 = 0.716 kN, 290 N ÷ 1,000 = 0.290 kN, and 1.66 g ÷ 1,000 = 0.00166 kg.

A 6 mm shaft and 12 mm housing bore do not distinguish these offers. EZO’s plain MR126 is 3 mm wide; its two closed variants are 4 mm wide. RCL’s table prints 4 mm under plain MR126 without a closure column. Preserve that original designation and obtain its closure drawing rather than silently treating it as either EZO variant.

Identical EZO loads and dimensions do not preserve the speed entry.

EZO’s MR126ZZ and MR126 2RS pages both give 716/293 N, eight balls of 1.588 mm, 4 mm inner- and outer-ring widths, and a 1.57 g versus 1.62 g reference mass. Their published grease speeds differ by 11,000 min⁻¹: 50,000 for ZZ and 39,000 for 2RS. Their oil entries differ by 20,000: 59,000 and 39,000.

Those differences come directly from two rows of the same maker, so a seal change cannot retain the ZZ speed entry simply because the dimensions and load ratings still match. An offer requiring grease speed above 39,000 min⁻¹ exceeds the published EZO 2RS entry. The larger ZZ number is not, by itself, an approval of the assembly’s operating condition.

For these two EZO configurations, the shaft-abutment entry is 7.1 mm, the housing-abutment entry 11 mm, and the maximum shaft/housing fillet radius 0.2 mm in both sources. Their published mounting limits match while their speed entries do not. Keep the required closure and lubricant with the speed requirement on the quotation line.

Rubber-sealed and metal-shielded miniature bearing samples occupy separate inspection dishes
Illustrative seal and shield examples; the offered configuration must match its own catalogue row.

NSK’s current comparison is a complete MR126ZZMC3 part.

The inspected NSK part page [2] names MR126ZZMC3, identifies shields on both sides, radial internal clearance MC3 and ISO NORMAL CLASS tolerance. It lists 790 N dynamic, 292 N static and 43,000 min⁻¹ grease speed. No oil value appears in that part’s speed section.

NSK and EZO MR126ZZ both list eight balls of 1.588 mm, yet publish different dynamic ratings: 790 N and 716 N. Ball size and count therefore do not supply a common rating for the two offers. NSK’s MC3 designation also belongs to the specified NSK part; the EZO detail row does not select the same clearance code for an order.

Retain MR126ZZMC3 as the full comparison item when seeking an NSK quotation. For a China-made RCL offer, retain RCL’s own 716/290 N row and ask for its closure and clearance specification. A package label that says only MR126 and a shared 6 × 12 × 4 mm envelope leaves those choices unanswered.

Gloved hands pack miniature bearings into separate unprinted protective compartments
Illustration of separate sample handling; package identification should retain the complete ordered part number.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
RCL
MR126
Current RCL MR126 row:6/12/4mm,Cr716/Cor290N,grease43000/oil50000r/min,1.66g. Closure is not identified by a separate column.
0.716
RCL716N converted to0.716kN. NSK’s current MR126ZZMC3 figure790N belongs to that NSK part.
0.29
RCL290N converted to0.290kN; EZO293N and NSK292N remain separate source values.
43000500000.00166
RCL1.66g converted to0.00166kg.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish MR126.

RCL

Ningbo, Zhejiang, China

Thin-wall ball bearings for compact mechanisms

RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.

Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings

131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask RCL about MR126

Applications the publishing works state.

ApplicationStated by
BicyclesRCL
Circular loomsRCL
Encoders and motorsRCL
RoboticsRCL

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for MR126.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. RCL · MR126 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. RCL · MR-series original table ↗

    MR126 row: 6/12/4mm, 716/290N, 43000/50000r/min, 1.66g. No closure column. Checked2026-11-04.

  2. NSK · MR126ZZMC3 current part specification ↗

    Complete part: 6/12/4mm, 790/292N, grease43000min⁻¹, 0.00174kg; 8×1.588mm balls; ZZ, MC3, ISO NORMAL CLASS. Checked2026-11-04.

  3. EZO / Kitanihon Seiki · MR126 specification ↗

    6/12/3mm, 716/293N, grease50000/oil59000min⁻¹, 1.23g. Checked2026-11-04.

  4. EZO / Kitanihon Seiki · MR126ZZ specification ↗

    6/12/4mm, 716/293N, 50000/59000min⁻¹, 1.57g; 8×1.588mm balls; da7.1, Da11, fillet max0.2mm. Checked2026-11-04.

  5. EZO / Kitanihon Seiki · MR126 2RS specification ↗

    6/12/4mm, 716/293N, 39000/39000min⁻¹, 1.62g; 8×1.588mm balls; da7.1, Da11, fillet max0.2mm. Checked2026-11-04.

Guide checked 2026-11-04. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.