BearingIndex
THE BEARINGINDEX DIRECTORY

S6000ZZ/2RS — 10 × 26 × 8 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The original S6000 detail lists bore 10, outside diameter 26 and OPEN/shield width 8. The dimensional headings do not explicitly print a unit or a separate 2RS width. Historical mm interpretations remain labelled in the directory.

Deep groove ball

S6000ZZ/2RS

S6000ZZ/2RS is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. SXA publishes this item in its stainless range, separately from the steel 6000 entry. Matching numerical rows do not identify the delivered material or closure; the guide below explains what to carry into the order and lot inspection. The publishing works are in Zhejiang province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
10 unit unconfirmed
Outside D
26 unit unconfirmed
Width B
8 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The same catalogue numbers can describe two SXA material ranges. Keep the stainless requirement in the order.

SXA’s S6000ZZ/2RS page is in its stainless range. Its separate bearing-steel 6000ZZ/2RS page repeats the same dimensions, load numbers and limit-speed entries. A quotation copied from that numerical table can therefore look correct while leaving the material version unresolved. Specify the actual delivered build first; for a nominal 10 mm bore, then agree the applicable unloaded-clearance group before inspecting the lot.

A 10 / 26 / 8 quote does not distinguish S6000 from steel 6000.

Compare the original product identities: S6000ZZ/2RS [1] is under SXA’s stainless range; 6000ZZ/2RS [2] is under its bearing-steel range. Both pages give d 10, D 26, OPEN B 8 and shield B1 8; both repeat dynamic 4550, static 1970 and grease/oil limit-speed entries 25/30 under ×1,000 rpm. Those matching numbers are not material identification. The dimensional and load headings do not explicitly give their units, so they are also not a substitute for the selected drawing and confirmed rating units.

When comparing quotes, compare the supplied item, not just its numerical row. If a response says only “6000ZZ/2RS, 10/26/8”, it has not explicitly identified the stainless build requested here. Keep the material requirement and chosen closure in the returned specification and purchase order. The manufacturer’s combined title presents choices; it does not tell the buyer which closure is being shipped.

Example wording for a stainless enquiry: “Please quote the stainless S6000 entry, identify the complete delivered designation and selected closure, and state the ring and ball grades in the specification. Do not substitute the bearing-steel 6000 entry solely because its published numbers match.”

The material grade needs a precise name as well as the word “stainless”. On catalogue printed page 29 [3], the Chinese description says 9Cr18 (AISI 440), while the English line says 9Cr18 (AISI 440C). The same page’s composition table separates 9Cr18/440 and 9Cr18Mo/440C. Consequently, this page does not label a delivered S6000 lot as 440C. Put the agreed grade and standard in the order and keep the corresponding material evidence with it. An environmental or cleaning-fluid requirement needs its own agreed performance criterion; the S prefix is not a published water-ingress or chemical-resistance result.

For speed, read the correct row before evaluating the build. The exact S6000 web entry and the catalogue’s 6000/6000ZZ row both give grease 25,000 rpm and oil 30,000 rpm. The adjacent catalogue 6001 row gives grease 28,000 rpm; that number does not belong to 6000. A grease-duty requirement above 25,000 rpm has no support from the 6000 row. Even below that entry, the publications do not specify separate speed conditions for the offered stainless seal, grease fill and installed duty. Keep any selected-build rating separate from the generic row rather than treating an oil limit as permission for a greased sealed bearing.

At exactly 10 mm nominal bore, use the clearance row that ends at 10.

Once the supplied material and closure are defined, the clearance requirement must also identify a group. SXA’s deep-groove table, printed page 30 [3], uses bore in mm and clearance in µm. Its interval is labelled Over 2.5 / Up-to 10: exactly 10 mm belongs to that interval. The next row starts over 10, so its limits are not the correct reference for this nominal bore.

Agreed clearance groupPublished range at nominal 10 mmRange in the next bore interval — do not use for 10 mm
C20–7 µm0–9 µm
Standard C02–13 µm3–18 µm
C38–23 µm11–25 µm

A hypothetical 15 µm reading illustrates the receiving error. For an agreed standard-C0, nominal-10-mm reference, 15 µm lies outside the published 2–13 µm interval. Reading the next bore row would make it appear inside 3–18 µm. This is a table-reading example, not a measured S6000 lot or a complete acceptance procedure: the catalogue states that clearance is measured without load, and the agreed inspection method and measurement uncertainty still matter.

A clearance reading cannot identify the group on its own. For example, 12 µm lies within both the 10 mm C0 interval and the C3 interval. Keep the supplier’s specified group with the lot instead of inferring it from one measurement. Here “C0” names the standard clearance group; the similarly written static-load symbol elsewhere in a bearing specification describes a different quantity.

Do not apply these unloaded ranges to the clearance remaining in a press-fitted, hot operating assembly. That is a different check. The practical receiving sequence is to match the delivered designation and material evidence to the order, verify the agreed clearance group using its applicable nominal-bore row and unloaded method, and retain the result with the lot. Installed running requirements belong to the selected shaft/housing design. The publication does not provide a complete S6000 installation acceptance procedure.

What each manufacturer published.

ManufacturerBore d (unit unconfirmed)Outside diameter D (unit unconfirmed)OPEN / shield width (unit unconfirmed)Source recorded
SXA
S6000ZZ/2RS
10
Historical record: 10 mm. The product row gives 10 without an explicit dimension unit.
26
Historical record: 26 mm. The product row gives 26 without an explicit dimension unit.
8
Historical record: 8 mm. Both OPEN B and shield B1 are 8; a separate 2RS width is not listed.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish S6000ZZ/2RS.

SXA

Ningbo, Zhejiang, China

Miniature and ultra-thin-wall ball bearings

SXA publishes steel and stainless deep-groove bearings, miniature MR and inch R series, and flanged versions. Its catalogue offers several closures and material options. Select the complete supplied form when comparing quotes.

Published ranges: Miniature deep groove ball bearings · Flanged miniature bearings · Stainless steel bearings · Ultra-thin-wall miniature bearings

296 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask SXA about S6000ZZ/2RS

Request a quote for S6000ZZ/2RS.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. SXA · S6000ZZ/2RS source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. SXA · stainless S6000ZZ/2RS product entry ↗

    Stainless category and exact S6000 title; d10/D26, OPEN/shield widths8, load numbers4550/1970, grease25/oil30 under ×1000rpm. Dimensional/load units and selected 2RS operating conditions are not explicitly stated.

  2. SXA · bearing-steel 6000ZZ/2RS product entry ↗

    Bearing-steel category and separate 6000 title. Repeats the S6000 numerical row; used to show why matching published numbers do not establish the delivered material.

  3. SXA · original catalogue, materials and clearance ↗

    PDF17/printed29-30: Chinese/English material naming and separate composition rows; bore over/up-to intervals, clearance µm and unloaded condition. Exact nominal10 mm C2/C0/C3 ranges are used for table interpretation, not as measurements of a supplied lot.

  4. SXA · original catalogue, 6000 and neighbouring 6001 rows ↗

    PDF11/printed18: 6000/6000ZZ grease25/oil30 ×1000rpm. The next 6001/6001ZZ row has grease28/oil32; those numbers are not assigned to 6000. The table offers material choices without a separately rated stainless 2RS row.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.