CZ’s 69-series image gives W693 dimensions 3×8×4 mm. The separate 693 row is 3×8×3 mm. The series closure drawings do not identify a selected W693 seal, material or tolerance configuration.
Deep groove ball
W693
W693 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 3 × 8 × 4 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
W693 adds 1 mm of width to CZ’s 693 row; the bore and outside diameter stay the same.
CZ’s metric 69-series catalogue puts 693 and W693 on separate rows. Both list a 3 mm bore and 8 mm outside diameter, but their widths are 3 and 4 mm. Both also list the same dynamic/static load and grease/oil speed entries. For a compact motor or retained shaft assembly, verify the axial stack first, then identify the exact closure and lubrication configuration; neither the shared ratings nor the W prefix settle those choices.
The shared 3 mm shaft interface hides a different axial stack.
For one replaced bearing, the nominal width difference is 1 mm. Check where the actual inner- and outer-ring faces locate against shoulders, spacers and retaining hardware. A 693 selected from the shared 3×8 mm diameters does not preserve a stack designed for W693’s 4 mm width. The table gives no assembly endplay, preload or authorised spacer alteration; obtain the controlled interface drawing before changing the stack.
The two rows’ identical 560/180 N ratings do not establish identical geometry beyond their recorded dimensions. They also do not show that the wider W693 carries more load, or that the 0.1 g mass difference ranks quality. Dynamic and static ratings are separate quantities; adding them does not create a 740 N allowable working load.
This catalogue does not define W as a material prefix. Specify the required ring, ball, cage and closure materials in the actual offer; do not turn W693 into a stainless-steel claim. Its series section shows d, D and B, but supplies no W693-specific shoulder, chamfer or tolerance limits for manufacturing the mating parts.
A 65,000 rpm enquiry needs more than the larger of two catalogue numbers.
Both CZ rows [2] list grease 61,000 rpm and oil 68,000 rpm. The image also sketches several closure forms, without dividing the W693 row into separately rated closure variants.
Published evidence
Reading for W693
Information needed for the offer
Grease speed 61,000 rpm
A 65,000 rpm requirement is above this entry.
Specific grease, fill, closure, loads and thermal conditions; obtain an assessed duty.
Oil speed 68,000 rpm
A separate lubrication entry, not an upgrade to the grease figure.
Actual oil delivery and operating arrangement with the selected bearing construction.
Series closure sketches
Open, shield/seal and retaining-ring examples are illustrated.
Complete available W693 variant and its drawing; the sketches alone do not establish availability or speed for every form.
CZ’s separate closure comparison [3] classifies ZZ and 2RZ as non-contact, low-torque forms with poor qualitative water performance. It describes 2RS as contact with medium torque, and 2RS1 as a higher-torque sealing route. Those are general selection distinctions, without measured W693 torque, an IP grade or a W693 water-ingress result.
For a high-speed motor exposed to water, identify both requirements in the same enquiry. A “better sealing” choice and a catalogue oil-speed entry do not jointly prove that the proposed W693 build meets 65,000 rpm. Ask CZ to identify the offered closure, lubrication arrangement and a trial covering temperature, torque and the actual exposure.
The 69-series illustration also uses LLB, LLH and LLU labels, while the engineering comparison uses 2RZ, 2RS and 2RS1. The examined pages do not provide a W693-specific cross-reference linking these names. Keep the supplier’s complete selected designation and drawing rather than silently translating one label into another. Confirm the operating figures for that configuration before treating a quotation as technically accepted.
What each manufacturer published.
Manufacturer
Bore (mm)
Outside diameter (mm)
Width (mm)
Source recorded
CZ W693 CZ lists W693 at width 4 mm and 693 at width 3 mm. Their shared 3 mm bore and 8 mm outside diameter do not make them axial replacements.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.
CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.
Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs
72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
693 3/8/3 mm and W693 3/8/4 mm; both Cr 560/Cor 180 N and grease/oil 61,000/68,000 rpm. Mass 0.0006/0.0007 kg. Series closure sketches do not define the selected W693 build or W material meaning.
Qualitative ZZ/2RZ/2RS/2RS1 contact, torque and protection comparison; no measured W693-specific configuration approval or mapping to every label on the 69-series illustration.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies