BearingIndex
THE BEARINGINDEX DIRECTORY

CZ

CZ / Cixi Lisheng: miniature and small motor-bearing enquiries with published endurance conditions, closure comparisons and process-capability targets to turn into a part-specific qualification plan.

CZ · MOTOR BEARINGS · QUALIFICATION PLAN

Turn CZ’s test examples into a trial for your actual motor.

Cixi Lisheng’s official introduction positions CZ around miniature/small motor bearings with a stated Φ3–Φ30 range. It names roundness, profile, roughness, S0910 vibration and BVT inspection routes, and publishes separate engineering pages on endurance, heat, speed, noise and sealing. These manufacturer statements are useful starting points for a qualification discussion, rather than proof that every offered part has passed the same tests. Company introduction [1]

Prepare a sourcing inquiry
01

CZ publishes two different endurance examples. Keep their conditions separate.

Published examplePart and test conditionsWhat to ask before relying on it
Long-life development pageABLT-3; 1 kN radial and 500 N axial load; 15,000 rpm; 1,000 hours before disassembly.Exact bearing/build, sample count, lubricant, temperature, test dates and inspection criteria; the text does not identify the tested designation.
Reliability report example6205ZZ; ABLT-1; 4,000 rpm; 4.85 kN radial, zero axial load; grease lubrication; stated L10 = 100 h.Complete approved report, lot identity, failure criteria and treatment of stopped/unfailed samples; this is a different part and duty.

The first page reports no observed damage after disassembly. The 6205ZZ table instead records six failed samples and two marked without failure at 360 hours. Do not merge the examples into “all CZ bearings last 1,000 hours”, or calculate a guaranteed service life from those eight rows. Long-life example [2] Reliability example [3]

Request the approved version.

The public reliability table leaves test dates and approval fields blank. Its own notes require stamps/signatures and limit the report to the submitted samples. Use it to discuss the supplier’s method; request an identifiable approved report for the offered construction, followed by a trial in your real motor and duty cycle. Report and validity notes [3]

02

Agree the sealing and thermal compromise before choosing a suffix.

Low starting torque or high speed

CZ’s comparison labels ZZ and 2RZ as non-contact routes with low torque. Ask for measured starting/running torque at your temperature and speed, and the actual contamination test. The site’s qualitative “poor” water performance is a reason to examine the whole enclosure, not to assume these closures protect a washing application.

Water or contamination exposure

The same comparison identifies 2RS as contact and 2RS1 as a higher-torque route with stronger qualitative sealing ratings. Agree the spray, dust or wash cycle and leakage/ingress criteria for the offered part and assembly; no IP grade or quantified sealing result is established by that table. CZ closure comparison [4]

CZ’s heat page compares NBR, HNBR, FKM/FPM and ACM materials, with its displayed temperature ranges labelled in Fahrenheit. Those general material ranges are not a Celsius bearing operating rating. Ask for the actual seal compound, cage, clearance and grease, plus continuous/peak duty and cold-start torque. The supplier itself recommends operating below a lubricant’s limit for satisfactory duration. Seal materials and lubricant discussion [5]

The high-speed page illustrates why external surface temperature alone may miss internal heating. Request the sensor location/method, ambient/cooling conditions, load, speed and lubricant for your trial; its illustrative temperatures are not a model-specific speed/temperature guarantee. High-speed thermal discussion [6]

03

Define the noise result your finished motor needs.

The introduction associates its stated EMQ tiers with Z/V designations, while the low-noise page discusses raceway finishing, cage construction, grease cleanliness and wear-particle analysis. Ask which of these controls applies to the quoted build, and obtain agreed vibration measurements with instrument, speed, load, frequency bands and limits. Published tiers/instruments [1] Low-noise engineering discussion [7]

Then test installed sound and vibration with the actual shaft/housing fits, rotor balance, preload and assembly process. Do not treat an EMQ tier as an acoustic guarantee for your finished tool. The low-noise page also makes a general friction-reduction claim without a part-linked baseline; use measured torque/temperature on your trial instead of carrying that percentage into a purchase specification. Scope of the published discussion [7]

04

Resolve the part drawing, then request the data behind the capability target.

The official 69-series image lists 693 as 3 × 8 × 3 mm and W693 as 3 × 8 × 4 mm. The width difference is useful for an axial-stack check: retain the complete designation and request the offered-part drawing, closure and tolerance. It does not establish that every suffix is available in both widths. 69-series dimensioned image [8]

The site’s process study specifies Ppk ≥ 1.67 for trial production and Cpk above 1.33 for continuing production, with stated sampling guidance and corrective controls. Those are published targets, not demonstrated results for your part. Identify critical drawing characteristics, obtain raw measurements, measurement-system evidence, stability plots and the actual study for the proposed line/lot, then agree containment and notification when targets are missed. Process-capability plan [9]

Nonstandard parts, stainless bearings and bushings have separate official product entries, but the reviewed pages do not provide complete text specifications. Send a controlled drawing and require a part-specific material/BOM and acceptance plan rather than borrowing the motor-bearing description for those products. Nonstandard route [10] Stainless route [11] Bushing route [12]

05

Check the current company, site and document scope.

The official site identifies 慈溪利升轴承有限公司, CZ, 华鹏路119号 in Cixi’s Kandun area, telephone 086-574-63071117 and [email protected]. A September 2021 environmental-impact report on a Zhejiang government host identifies the same company and site for a proposed annual 60-million bearing project. A project report supports historical entity/site context; it does not establish today’s output or product quality. Official company/contact details [1] Government-hosted project report, cover and printed pages 1/4 [13]

The website gives a 2005 origin, while that report describes establishment in October 2009. Confirm the legal entity and operating history on current business documents before contracting; do not silently combine the dates. The introduction also claims IATF16949/ISO9001 and chemical-compliance qualifications. Request current issuer-verified certificates and relevant material declarations with legal name, site, scope and validity, rather than treating a general claim or certificate-gallery title as part approval. Manufacturer statements [1] Historical project description [13] Certificate gallery [14]

YOUR NEXT STEP

Send CZ a motor-bearing trial brief

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

72 model records
Model / bearing familyManufacturerBore dOutside DWidth B / T / LDetails

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Manufacturer statementCZ · company introduction ↗

    Motor-bearing positioning, stated range/tier/equipment, origin and contact/certificate claims; not independent audit.

  2. Manufacturer test descriptionCZ · long-life development example ↗

    ABLT-3 load/speed/time and disassembly statement; unnamed tested part and incomplete report details.

  3. Manufacturer report exampleCZ · 6205ZZ reliability example ↗

    Reviewed text and displayed table: conditions/eight sample rows and validity notes; blank date/approval fields, no current offered-part guarantee.

  4. Manufacturer engineering comparisonCZ · dust/water closure comparison ↗

    Qualitative ZZ/2RZ/2RS/2RS1 trade-offs; no IP grade or measured ingress qualification.

  5. Manufacturer engineering discussionCZ · seal materials and temperature ↗

    General seal materials with Fahrenheit ranges and lubricant considerations; not model operating limits.

  6. Manufacturer engineering discussionCZ · high-speed thermal discussion ↗

    Internal/external heating illustration; no part-specific rated speed inferred.

  7. Manufacturer engineering statementCZ · low-noise engineering ↗

    Raceway/cage/grease/particle routes; no independently measured friction or installed acoustic guarantee.

  8. Manufacturer dimensioned tableCZ · 69-series image catalogue ↗

    Image visually reviewed: mm fields and 693/W693 widths; actual quoted variant requires drawing.

  9. Manufacturer quality planCZ · initial process study/capability plan ↗

    Published Ppk/Cpk targets and sampling/containment; not actual production study results.

  10. Manufacturer product entryCZ · nonstandard product route ↗

    Category/product route without complete text specification.

  11. Manufacturer product entryCZ · stainless product route ↗

    Published route; alloy and actual offered specification need confirmation.

  12. Manufacturer product entryCZ · bushing product route ↗

    Separate bushing route; no motor-bearing properties transferred.

  13. Government-hosted project documentZhejiang government host · Lisheng project EIA, September 2021 ↗

    48-page report reviewed for cover/entity/site and planned project; not current output, environmental acceptance or product approval.

  14. Manufacturer galleryCZ · certificate gallery ↗

    Published gallery titles only; current issuer/legal/site/scope/validity not established.

Report a source correction → · Return to inquiry checklist ↑

CZ published product scope reviewed

The manufacturer website describes miniature motor bearings and inch series.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:34

Source documentation retained for editorial review.