Yifeng
NBLY / Ningbo Yifeng: miniature and small deep-groove bearings, including explicitly published inch and nonstandard enquiry references.
Preserve the unit, closure and complete reference when replacing a small bearing.
Ningbo Yifeng identifies NBLY as its own bearing brand and describes miniature/small deep-groove, inch and nonstandard manufacture. Its official range includes metric model pages, an R2A inch reference, and separate 923 and 923/3.175 nonstandard entries. Begin with the particular interface and build, then qualify it for the actual motor or machine position. Company and brand [1] R2A [2] MR104 [3]
R2A and MR104 need different dimension conversations.
| Official reference | Published bore / OD | Open / closed width | Before approving the assembly |
|---|---|---|---|
| R2A | 3.175 / 12.700 mm 0.125 / 0.500 inch | 4.366 / 4.366 mm | Use the specified unit system and controlled tolerances; request the actual closed form and offered BOM. |
| MR104 | 4 / 10 mm | 3 / 4 mm | Recheck the axial shoulder/spacer/retention stack when moving from open to closed. |
These entries preserve the explicit open/closed fields on Yifeng’s product tables. “Closed” is not enough to specify a shield, contact seal or low-torque non-contact seal; ask for the complete offered designation and section. Equal external width on R2A does not establish equal running torque or environmental protection. R2A dual-unit table [2] MR104 product table [3]
Send the shaft/housing drawing in its original units and identify dimensions requiring limits rather than converting rounded catalogue numbers into manufacturing tolerances. Keep the closed-form designation, clearance, cage and lubricant on the sample and production specifications.
Reconcile catalogue fields, then define the nonstandard part.
MR104: choose a controlled source
The product page gives dynamic/static ratings of 715/265 N and a 0.15 mm chamfer entry. The dated miniature technical table gives 708/266 N and two minimum radius fields of 0.2/0.15 mm for MR104. Do not combine the larger rating with the smaller mounting radius or average the figures. Ask which revision/build applies, and confirm shaft/housing corner clearance against the actual drawing. Product fields [3] 30 April 2025 technical table [4]
923 and 923/3.175: obtain the section
The website lists these as separate nonstandard products. Their reviewed parameter areas do not provide a numerical specification. Retain the complete slash reference, but do not infer that the suffix establishes the bore or that all other dimensions match 923. Send the existing part’s full markings, measured interface and controlled drawing, then request the offered section/BOM and acceptance requirements. 923 entry [5] 923/3.175 entry [6]
The larger technical table separately lists groove and snap-ring fields and N/NR variants, for example on 6900. If axial retention is involved, include the actual groove/ring/housing interface and supplied-ring requirement in the enquiry. Do not infer that every basic reference includes a ring or that a catalogue load rating approves the retained assembly. The table’s speed column is labelled ×1,000 rpm; qualify actual speed with closure, grease and load conditions rather than copying a bare table number into an operating limit. Larger technical table [7]
Turn a private-label enquiry into a traceable approved build.
Yifeng states both its own NBLY brand and private-label production experience. No customer identities or buyer-specific approvals are established by that statement. For an OEM order, agree whose drawing controls the part, how markings and packaging identify the manufacturing lot, and who approves changes to seals, grease, clearance or manufacturing site. Brand/private-label statement [1]
- Define the motor position: provide load/speed/start-stop duty, shaft/housing fits, temperature and contamination. A wiper, condenser fan and vacuum motor do not share an automatic approval merely because the same catalogue family is offered.
- Approve samples on two levels: agree bearing geometry/runout and torque/noise methods, then test in the actual motor under the specified duty. Record numerical acceptance, warm-up and fixture conditions.
- Release repeat supply: retain drawing/BOM revision, sample lot and reports; agree production sampling, material/heat-treatment and lubricant traceability, nonconformance response and requalification triggers.
The homepage also mentions security and humanoid-robot applications. These are manufacturer application statements, not proof of a complete robot-joint bearing, specific robot load/stiffness qualification or customer approval. Its production-line/output descriptions and facility gallery do not establish available capacity for your offered build; request the relevant process route, inspection/calibration records and a dated production slot. Homepage application statements [8] Facility publication [9]
Check scope and the manufacturing address together.
The manufacturer’s certificate gallery publishes an ISO9001 image numbered 05324Q31405R0S, with deep-groove bearing and component manufacture and printed validity 19 June 2024–18 June 2027. Its IATF16949 image states deep-groove bearing manufacture excluding product design, clause 8.3, and a printed expiry of 29 March 2027. These are reviewed manufacturer-displayed documents; their present status has not been independently confirmed. Original certificate publication [10]
East Road 387 versus West Road 588
Both displayed system documents identify Huancheng East Road 387, Zhouxiang, while the current contact page gives Huancheng West Road 588. Obtain the current certificate/site annex, scope and issuer verification for the plant that will fulfil the order. Do not infer a move or extend one address’s coverage to another without documents. Certificate site [10] Current contact address [11]
The ISO issuer’s public query required a security verification after the certificate number was entered, preventing status confirmation in this review. Recheck with the issuer/CNCA and request the applicable current IATF record; future dates printed on an image alone do not establish active status. Management-system scope also does not approve an individual motor or robot application. ISO issuer query route [12]
A government-hosted orderly-electricity-use list identifies the exact legal entity in Zhouxiang. Use it only as location/entity context; the plan classes are not quality ratings and this record does not establish current power restrictions, capacity or delivery risk. The official order-contact route is 15058410995 / [email protected]; match the quotation, plant and traceability documents to 宁波伊锋轴承有限公司. Government entity entry [13] Official contacts [11]
Prepare an NBLY/Yifeng controlled-build enquiry
Tick what you have ready. Copy the full checklist with its current status for your procurement notes.
Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.
Documented models.
3 model recordsEvidence, with boundaries.
Our review approach →Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.
- Manufacturer publicationYifeng · company / NBLY brand ↗
Small/inch/custom range and own-brand/private-label statements; no named customer, capacity audit or available production slot inferred.
- Manufacturer model tableYifeng · R2A dual-unit product table ↗
Paired mm/inch and open/closed width; no complete closure/BOM or interchange approval.
- Manufacturer model tableYifeng · MR104 product table ↗
4/10 mm, open3/closed4, 715/265 N and 0.15 mm radius entry; differs from technical-table fields.
- Dated manufacturer technical referenceYifeng · miniature technical table, 30 April 2025 ↗
MR104 708/266 N, r/r1 fields and explicitly scaled speed; controlled revision/conditions need confirmation.
- Manufacturer reference displayYifeng · 923 nonstandard entry ↗
Actual named entry; numerical parameter area unfilled in reviewed page, no dimensions invented.
- Manufacturer reference displayYifeng · 923/3.175 nonstandard entry ↗
Distinct full designation; slash suffix not used to infer bore or interchangeability.
- Dated manufacturer technical referenceYifeng · larger deep-groove technical table ↗
Separate groove/ring fields, N/NR entries and ×1000rpm heading; not a retained-system qualification.
- Manufacturer application statementsYifeng · homepage application routes ↗
Motor/security/humanoid-robot routes; no robot system rating, customer or independently verified application approval.
- Manufacturer facility publicationYifeng · plant/equipment gallery ↗
Published gallery/production descriptions; part-linked capability, calibration and schedule require confirmation.
- Manufacturer certificate imagesYifeng · certificate gallery ↗
ISO and IATF originals visually read, East Road387 scope/dates and product-design exclusion; current status not independently verified.
- Manufacturer contact publicationYifeng · official contact page ↗
West Road588 and authorised enquiry route published; manufacturing/certificate coverage relationship needs documents.
- Primary issuer, query limitedNGV · certification query route ↗
Certificate05324Q31405R0S entered on 2026-10-08; security verification prevented a status result, not a negative finding.
- Government-hosted entity/location contextCixi government-hosted orderly electricity-use list ↗
Original PDF downloaded; exact Yifeng/Zhouxiang name located; no present restriction or production/quality inference.
Report a source correction → · Return to inquiry checklist ↑
Yifeng published product scope reviewed
The manufacturer website describes miniature and nonstandard ball bearings.
Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.
Company-level record; not a model test report · 2026-09-24 04:20:34
Source documentation retained for editorial review.