BearingIndex
THE BEARINGINDEX DIRECTORY

6204 — 20 × 47 × 14 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

RCL, CZ and HCH explicitly label their 6204 boundary dimensions 20 × 47 × 14 mm. The examined Xinfeng, Global, Sihai and ZYS boundary columns do not state their unit. Keep each source’s unit status separate; the matching numbers do not supply the missing labels.

Deep groove ball

6204

6204 is a deep groove ball designation documented on BearingIndex from 7 manufacturer publications. The historical directory dimension interpretation is 20 × 47 × 14 (unit unconfirmed). Boundary unit labels differ between examined publications. See the source-by-source review. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
20 unit unconfirmed
Outside D
47 unit unconfirmed
Width B
14 unit unconfirmed

Compare the 7 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 6204 quote says 18,000 r/min with grease. Which catalogue supports it?

The examined Global catalogue gives 14,000 r/min with grease and 18,000 with oil; RCL gives 15,000 and 18,000. Neither examined row supports an 18,000 r/min grease claim. Ask for the actual offered construction and its supporting document before treating that quotation as a selection limit.

Follow the number back to its original column.

RCL’s 6204 row [1] labels its limiting-speed columns grease and oil: 15,000 and 18,000 r/min respectively. Global’s scanned catalogue, printed page 9 [3], gives 14,000 and 18,000 r/min. Xinfeng’s examined row [2] contains no speed field.

If the quote is for RCL and cites 18,000 as its grease figure, return the original row and ask which specific construction or newer document supports the change. Do not silently relabel its oil value. For Global, 18,000 also belongs to the oil column in the examined catalogue. A different grease figure requires a document for that offered construction; it is not supported by this row.

A missing speed for Xinfeng cannot be completed with either competitor’s figure. The speed comparison here uses these three sources. The four other recorded manufacturers have their own entries; their matching boundary numbers do not supply a missing speed or dimension unit in this comparison.

Read each unit label before comparing the matching dimension numbers.

FieldRCLXinfengGlobal
Bore / outside diameter / width20 / 47 / 14 mm20 / 47 / 14; boundary unit unstated20 / 47 / 14; boundary unit unstated
Dynamic / static rating12840 / 6553 N12.84 / 6.65 kN12840 / 6650 N
Grease / oil catalogue speed15000 / 18000 r/minNot stated14000 / 18000 r/min
Ball complement8 × 7.938 mm8 balls; size 7.938, unit unstated8 × 7.938 mm
Catalogue mass106 gNot stated0.098 kg (98 g)

RCL explicitly states millimetres for its boundary dimensions. Xinfeng and Global publish the same 20 / 47 / 14 numbers without a boundary-unit label; their numbers alone do not confirm a shared envelope. Xinfeng also leaves ball-size units unstated, while RCL and Global label that separate field in mm. The dynamic figures match after unit conversion; the static figures do not all match. Mass and static-rating differences are not a verdict on quality. Keep each row intact instead of combining the highest speed, lowest weight and a chosen rating into an invented ‘6204 specification’.

To compare prices, ask each shortlisted supplier to identify the offered suffix, clearance, closure, lubricant and conditions attached to its speed claim. If those differ, the next action is to resolve the construction and duty requirement; a price ranking would compare different offers.

Example: screening a proposed 16,000 r/min grease duty.

This is an illustrative input, not a tested machine. At 16,000 r/min, the proposed speed exceeds RCL’s published grease figure of 15,000. It also exceeds Global’s grease entry of 14,000. Xinfeng’s examined row supplies no speed with which to make that comparison.

That arithmetic supports three different enquiries: ask RCL for an explicitly qualified alternative or revised duty; ask Global for a qualified construction or supporting newer document for the actual duty; ask Xinfeng for a configuration-specific speed declaration. Neither examined grease row approves this duty. The comparison does not reject every construction available from either maker.

Do not substitute oil simply to use RCL’s 18,000 column unless the machine’s lubrication system and selected bearing are designed and approved for that change. The catalogue identifies a condition; it is not an instruction to modify the machine.

What each manufacturer published.

ManufacturerBore d — see source noteOutside D — see source noteWidth B — see source noteSource recorded
Sihai
6204
20
Boundary unit not stated
47
Boundary unit not stated
14
Boundary unit not stated
2026-09-24 source ↗Request
CZ
6204
20
mm explicitly stated
47
mm explicitly stated
14
mm explicitly stated
2026-09-24 source ↗Request
Yuyao Global
6204
20
Boundary unit not stated
47
Boundary unit not stated
14
Boundary unit not stated
2026-09-24 source ↗Request
RCL
6204
20
mm explicitly stated
47
mm explicitly stated
14
mm explicitly stated
2026-09-24 source ↗Request
Yuyao Xinfeng
6204
20
Boundary unit not stated
47
Boundary unit not stated
14
Boundary unit not stated
2026-09-24 source ↗Request
HCH
6204
20
mm explicitly stated
47
mm explicitly stated
14
mm explicitly stated
2026-09-22 source ↗Request
ZYS
6204
20
Boundary unit not stated
47
Boundary unit not stated
14
Boundary unit not stated
2026-09-22 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

Compare the recorded figures.

PropertyFindingSources
Bore d — see source noteAll 3 sources publish 203
Outside D — see source noteAll 3 sources publish 473
Width B — see source noteAll 3 sources publish 143

Where the figures differ, use the drawing from the manufacturer you buy from.

The works that publish 6204.

CZ

Ningbo, Zhejiang, China

Miniature motor bearings and inch series

CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.

Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs

72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask CZ about 6204

HCH

Zhejiang

Deep groove ball and tapered roller bearings

HCH publishes metric and inch ball bearings, tapered roller bearings and steel balls. Review the product route, production documents and export-entity evidence before sourcing.

23 designations documented here · source recorded 2026-10-08

Ask HCH about 6204

RCL

Ningbo, Zhejiang, China

Thin-wall ball bearings for compact mechanisms

RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.

Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings

131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask RCL about 6204

Sihai

Ningbo, Zhejiang, China

Deep groove bearings for motors and automotive use

Sihai publishes a separate automotive table with wider 63001 and 62201 references, plus high-temperature generator grease, C3 and seal-material statements. Compare the actual section and complete offered build rather than replacing these with similar ordinary catalogue numbers. Its displayed IATF document covers miniature deep-groove manufacture with product design excluded; request current verified status and a part-specific automotive approval package.

Published ranges: 6000, 6200 and 6300 series · 6800 and 6900 series · Automotive engine-bearing applications

85 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Sihai about 6204

Yuyao Global

Ningbo, Zhejiang, China

Miniature and small bearings

Global publishes ordinary shielded/sealed bearings alongside nonstandard steel and polymer pulley assemblies. Its scanned catalogue provides useful part-specific dimensions and construction examples; distinguish bore from shaft dimensions, match the complete assembly drawing, and confirm lubricant, noise testing and the current contracting entity.

Published ranges: Miniature and small bearings · Rubber-sealed bearing designs · Metal-shielded bearing designs

71 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Yuyao Global about 6204

Yuyao Xinfeng

Ningbo, Zhejiang, China

Small ball bearings and custom assemblies

Yuyao Xinfeng publishes bicycle headset, hub and bottom-bracket bearings alongside angular-contact pairs, steering and custom products. Match the assembly interface and pair arrangement to the offered drawing. Its published Zhejiang Made certificate covers a particular model; confirm that scope and current status for the proposed order.

Published ranges: Single- and double-row deep groove ball bearings · Metric and inch miniature bearings · Steering and bicycle-bearing designs · Thin-ring and nonstandard assemblies

36 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Yuyao Xinfeng about 6204

ZYS

Precision and special bearings

ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.

87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask ZYS about 6204

Applications the publishing works state.

ApplicationStated by
Automotive steeringYuyao Xinfeng
Automotive systemsSihai, Yuyao Global
BicyclesRCL, Yuyao Xinfeng
Brushless motorsCZ
Circular loomsRCL
Communications equipmentYuyao Global
DronesCZ
Encoders and motorsRCL
Garden toolsCZ
Household appliancesSihai, Yuyao Global
Medical equipmentYuyao Global
Office equipmentSihai
Power toolsCZ, Sihai
RoboticsRCL

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix.

Ask the manufacturer for these when you enquire.

Request a quote for 6204.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Sihai · 6204 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. CZ · 6204 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  3. Yuyao Global · 6204 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  4. RCL · 6204 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  5. Yuyao Xinfeng · 6204 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  6. HCH · 6204 source ↗

    Directory record dated 2026-09-22. Confirm the current complete designation and controlled drawing with this manufacturer.

  7. ZYS · 6204 source ↗

    Directory record dated 2026-09-22. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. RCL · actual 6204 table ↗

    20/47/14 mm, N ratings, ball complement, grease/oil speeds and 106 g mass. No motor approval established.

  2. Yuyao Xinfeng · actual 6200-series table ↗

    6204 boundary numbers, minimum-radius and ball-size numbers without dimension units; kN ratings and ball count. Speed, grease and mass not given in this row.

  3. Yuyao Global · manufacturer catalogue ↗

    PDF page 6, printed page 9: exact 6204 boundary numbers without a unit label, N ratings, speeds, ball complement with mm ball-size heading and mass. Manufacturer publication, not sample test.

  4. SKF · Bearing Installation and Maintenance Guide ↗

    Fits, clearance and mounting principles, printed pages 11–12. Background only; no SKF numerical fit or clearance imposed on another brand.

  5. CZ · original 62-series image ↗

    6204 boundary row 20/47/14; d/D/B heading explicitly mm. Used for unit status only.

  6. HCH · current 62-series table ↗

    6204 boundary row 20/47/14 in paired mm/inch columns. Used for unit status only.

  7. Sihai · original 6200-series table image ↗

    6204 boundary row 20/47/14; examined boundary heading does not state unit. Used for unit status only.

  8. ZYS · current 6200-series table ↗

    6204 boundary row 20/47/14; examined Dimension heading does not state unit. Used for unit status only.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.