Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
623
623 is a deep groove ball designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 3 × 10 × 4 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Six balls or eight: are these two 623 bearings the same replacement?
RCL and Xinfeng both publish 3 × 10 × 4 mm for 623, but their tables describe different ball complements. The envelope matches; the internal data do not. Compare the requirement of the old assembly before accepting either as an equivalent part.
The two official rows show the difference, not a quality ranking.
Published field
RCL 623 [1]
Xinfeng 623 [2]
d / D / B
3 / 10 / 4 mm
3 / 10 / 4 mm
Ball complement
6 balls, diameter 1.588 mm
8 balls, diameter 1.3 mm
Dynamic / static rating
582 / 196 N
0.5 / 0.19 kN
Catalogue speed, grease / oil
40,000 / 48,000 r/min
Not stated in the examined row
Other row fields
Approximate mass 1.6 g
Minimum radius 0.15 mm
RCL’s original units are N [1]; Xinfeng’s are kN [2]. Converting Xinfeng’s figures gives 500 / 190 N. Eight smaller balls do not make this row the higher-rated one. Neither ball count nor the small static-rating difference is a measure of product quality.
The data also do not establish starting torque, running sound or wear in your mechanism. Those are not columns in either row. In particular, Xinfeng’s missing speed cannot be filled with RCL’s 40,000 r/min just because both bearings have the same dimensions.
What must stay the same in the old 3 mm-shaft assembly?
If the original specification names a maker and complete suffix, identify those before reducing the order to ‘623’. Ask the alternate supplier to declare the exact offered closure, clearance, lubricant and ball complement. The comparison above describes catalogue rows, not the delivered configurations.
For a load-driven choice, give the supplier the bearing loads and target duty so the selected row can be assessed. For a mechanism whose limiting requirement is starting torque or running resistance, ask for the measurement condition and result for the offered configuration. A capacity comparison does not answer that requirement, and the catalogue speed column is not a torque result.
For an existing drawing that uses RCL’s six-ball design, an eight-ball offer is a construction change to review. It is not automatically unacceptable, but the drawing’s functional requirements need evidence from that offered item. A drawing that specifies only 3/10/4 leaves those requirements undefined; obtain them from the assembly owner before signing off an alternate.
The useful supplier response
It names the complete 623 construction and answers the specific missing requirement of the old assembly. A response that repeats the dimensions or says ‘more balls’ has not demonstrated equivalence.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Compare the recorded figures.
Property
Finding
Sources
Dynamic load rating
Ranges 0.5 – 0.582 kN across 2 sources
2
Static load rating
Ranges 0.19 – 0.196 kN across 2 sources
2
Where the figures differ, use the drawing from the manufacturer you buy from.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
3.5 mm
Mean diameter dm
(D + d) / 2
6.5 mm
C / C₀ load ratio (2 sources)
dynamic ÷ static load rating
RCL 2.97 · Yuyao Xinfeng 2.63
Arithmetic on the figures above — not a bearing life calculation for your load case.
RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.
Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings
131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Yuyao Xinfeng publishes bicycle headset, hub and bottom-bracket bearings alongside angular-contact pairs, steering and custom products. Match the assembly interface and pair arrangement to the offered drawing. Its published Zhejiang Made certificate covers a particular model; confirm that scope and current status for the proposed order.
Published ranges: Single- and double-row deep groove ball bearings · Metric and inch miniature bearings · Steering and bicycle-bearing designs · Thin-ring and nonstandard assemblies
36 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix.
Ask the manufacturer for these when you enquire.
Other designations with the same 3x10x4 mm envelope.
623 3/10/4, radius 0.15, kN ratings and eight 1.3 mm balls; no speed, torque or installation approval established.
Guide checked 2026-10-08. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies