Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
6914
6914 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 70 × 100 × 16 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
It has the same boundary size, 70 × 100 × 16 mm, but the load ratings are not a property of that size. RCL, NSK and SKF each publish their own ratings for this envelope, and the three sets differ. Compare an offer only with the ratings of the maker who will supply it.
One envelope, three sets of ratings.
All three sources below list a 70 mm bore, 100 mm outside diameter and 16 mm width. Their load ratings and speed figures are not the same, so a rating copied from one maker cannot stand for another maker’s bearing.
SKF publishes a reference speed and a single limiting speed; RCL and NSK publish separate grease and oil limits. These are different definitions, so the SKF speed figures do not line up with the other two columns.
The same ball set, different dynamic ratings
RCL prints 17 balls of φ8.731 mm for 6914, and NSK prints the same count and diameter. Their dynamic ratings still differ: 23,570 N against 26,100 N. The internal geometry visible in a catalogue row does not make one maker’s rating valid for the other. If your design calculation depends on Cr, use the figure of the supplier you are buying from and ask how it was determined.
RCL’s table is in newtons and grams.
RCL’s 69-series table [1] heads its rating columns N and its mass column g. The directory table on this page shows those values converted to kN and kg: 23,570 N is 23.57 kN, and 327 g is 0.327 kg. The conversion is arithmetic, not a different published value.
The table lists one 6914 row and no shielded or sealed 6914 row. RCL’s English series page [2] says the 69 series is produced open, shielded or sealed, but it does not print a separate 6914-ZZ or 6914-2RS line. If you need a closed bearing, ask RCL for that complete designation and its own row; do not assume the open bearing’s speeds apply to it.
The mounting dimensions here come from NSK, not RCL.
These are NSK’s limits for an NSK bearing. For an RCL offer, ask RCL for its 6914 drawing with chamfer limits and recommended shoulder diameters, and check your shaft and housing drawings against those figures.
What each manufacturer published.
Manufacturer
Dynamic load rating (kN)
Static load rating (kN)
Limiting speed — grease (rpm)
Limiting speed — oil (rpm)
Reference mass (kg)
Source recorded
RCL 6914 RCL’s current 69-series row prints 6914 as d70/D100/B16 mm, Cr 23570 N, Cor 21250 N, 17 balls of φ8.731 mm, grease 6300 and oil 7500 r/min, 327 g. The ball columns are not part of the stored record; they are shown here from the same row.
23.57 RCL prints 23570 N in a column headed N. Shown here converted to kN.
21.25 RCL prints 21250 N in a column headed N. Shown here converted to kN.
6300
7500
0.327 RCL prints 327 g in a column headed g. Shown here converted to kg.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
15 mm
Mean diameter dm
(D + d) / 2
85 mm
C / C₀ load ratio
dynamic ÷ static load rating
RCL 1.11
Arithmetic on the figures above — not a bearing life calculation for your load case.
RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.
Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings
131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Row 6914: 70/100/16 mm, Cr 23570 N, Cor 21250 N, 17 balls φ8.731 mm, grease 6300 / oil 7500 r/min, 327 g. Header units N, mm, r/min, g. No closure-variant row. Read 2026-10-30.
NSK values only: 70/100/16 mm, Cr 26100 N, C0r 21200 N, grease 6300 / oil 7500 min⁻¹, 0.349 kg, 17 balls 8.731 mm, r min 1, da 75–77.5, Da max 95, ra max 1 mm. Read 2026-10-30.
SKF values only: 70/100/16 mm, C 23.8 kN, C0 18.3 kN, reference speed 14 000 r/min, limiting speed 8 500 r/min. No source states that 6914 and 61914 are the same product; only the boundary dimensions coincide. Read 2026-10-30.
Guide checked 2026-10-30. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies