GOOT
GOOT / Ningbo Goot: a sourcing guide for its published small deep-groove and angular-contact routes, with clear limits on older catalogue and certificate evidence.
Use the catalogue to identify the part, then qualify the current offer.
Ningbo Goot describes high-precision miniature/small deep-groove and angular-contact ball bearings, and names machine-tool spindles, engraving machines and several motor applications. Company introduction [1] Its product navigation separates metric, inch, thin-section, stainless and flange routes. Product catalogue [2] The reviewed website carries older dates, so the current offered variant and its supporting records require direct confirmation.
The metric table separates open, shielded and sealed choices.
The metric catalogue has separate designation columns for open, shielded and sealed products. For example, it lists 623 / 623ZZ / 623-2RS and 608 / 608ZZ / 608-2RS. Other entries have a blank or dash in a variant field. It labels rated loads in N and speed limits in rpm, with separate grease and oil columns. [2]
| When preparing the request | Keep this distinction visible |
|---|---|
| Replacing an existing bearing | Record the whole marked code, closure, grease information and original drawing. A base number alone leaves the catalogue’s variants unresolved. |
| Choosing the closure | Describe contamination, lubricant retention, torque/noise and temperature requirements. Ask GOOT which actual shield/seal construction it proposes and how it will be accepted. |
| Using catalogue speed data | Request the current part sheet and applicable lubrication, closure and operating conditions. The two speed columns are not an unconditional speed guarantee for all variants. |
| Finding a blank variant field | Ask whether the required version is offered. A dash is not a current stock report or a reason to substitute another closure without engineering approval. |
The dated closure article uses Z/2Z and RS/2RS notation and says special orders should state grease grade and fill quantity. [6] Put those two inputs in the request and ask for the current offered specification. Its broad temperature statement is not carried forward here as a validated limit for every present GOOT part.
This guide does not republish the numerical load/speed values or silently repair apparent inconsistencies in the old table. Use a manufacturer-confirmed, controlled sheet for design calculations and the offered variant.
Separate an angular-contact spindle project from a deep-groove motor request.
GOOT’s introduction puts miniature deep-groove and angular-contact products together, but its application examples include both precision machine-tool/engraving spindles and motors in air conditioning, extraction, vacuum-cleaning and automotive equipment. [1] Our suggested qualification routes keep those assemblies distinct.
Angular-contact spindle inquiry
Provide the spindle-bearing arrangement, position and assembly drawing. State speed range, load directions, required running accuracy, temperature and the intended preload/matching arrangement. Ask for the exact contact design, precision and pairing instructions of the proposed product.
The introduction does not supply a specific spindle-bearing designation, qualified preload or measured running result. Request those records before treating an “import replacement” marketing objective as interchangeability.
What should the sample comparison hold constant?
The assembly drawing, fits, mounting method and test duty. Record which bearing construction, closure, grease and any preload change. Require a documented acceptance result for the installed sample and agreed notice of changes affecting the approved configuration.
Order the packaging and identifying marks deliberately.
The 14 June 2017 packaging article describes plastic tubes, rust-prevention paper/cartons and individual bags/boxes, and says packing can be specified when ordering. It also describes outer-carton markings for quantity, mass, date, volume and bearing designation. [7] This is a useful historical description, not a confirmed current packaging offer.
Ask which option is available for the quoted quantity and destination. Agree the exact part/variant printed on the label, lot or batch identification, quantity per pack and documents supplied with the shipment. For distributor or small-quantity replenishment, confirm whether individual packs retain enough identification to trace a bearing after the carton is opened.
Older technical material needs a current order-level confirmation.
The company introduction refers to ISO 9001:2008 and ISO/TS 16949:2009. [1] These are the versions written on the reviewed page; they are not evidence of a valid current certificate. Ask for the applicable issuer, certificate number, expiry and manufacturing-site scope, then verify the record.
The technical index dates its listed topics—noise/vibration, closure, lubrication, clearance, precision and packaging/marking—to 14 June 2017. [3] Some linked article bodies were not obtained in this review. We have not turned those headings into current testing specifications or claimed to have read unavailable content. Ask for the relevant current procedure, acceptance limit and drawing/packaging requirements directly.
A government-hosted 2024 technology-based SME list includes 宁波固特轴承有限公司 with entry 2024330211A9000302. [4] This dated record helps cross-check the company name; it does not establish bearing qualification, present programme validity, available capacity or delivery.
The official contact page provides a company enquiry route. [5] Confirm the current receiving contact, manufacturing address and legal contracting entity before sending drawings or arranging a visit. The reviewed address page did not provide a readable street address, so this guide does not choose a current plant address from an older unrelated record.
Prepare a GOOT variant-specific inquiry.
Tick what you have ready. Copy the full checklist with its current status for your procurement notes.
Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.
Documented models.
6 model recordsEvidence, with boundaries.
Our review approach →Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.
- Manufacturer publication with older certificate versionsGOOT · company introduction ↗
GOOT identity, miniature/deep-groove/angular-contact positioning and application examples. Old certificate-version and scale statements are not current qualifications.
- Manufacturer catalogueGOOT · metric catalogue and product-family navigation ↗
Separate open/ZZ/-2RS designations, grease/oil speed columns and family routes. Current controlled specifications and availability require confirmation.
- Dated manufacturer technical indexGOOT · technical-material index ↗
2017 topic listing only; some linked article text was unavailable in this review, so no underlying procedures are inferred.
- Dated government listGovernment-hosted Ningbo 2024 technology-based SME list ↗
Company name and 2024 programme entry; not current programme status, product certification or factory capacity.
- Manufacturer contact pageGOOT · official contact route ↗
Published contact route on an older website; current recipient, plant address and contract identity still need direct confirmation.
- Dated manufacturer technical articleGOOT · shields and seals, 14 June 2017 ↗
Published closure notation and grease-order inputs; broad historical temperature statement is not treated as a current variant-specific qualification.
- Dated manufacturer technical articleGOOT · packaging and marking, 14 June 2017 ↗
Historical packing/marking options; availability, lot identification and agreed shipping labels must be confirmed for the order.
Report a source correction → · Return to inquiry checklist ↑
GOOT published product scope reviewed
The manufacturer website describes deep groove ball bearings and miniature variants.
Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.
Company-level record; not a model test report · 2026-09-24 04:20:33
Source documentation retained for editorial review.