Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
16002
16002 is a deep groove ball designation documented on BearingIndex from 6 manufacturer publications. The published boundary dimensions are 15 × 32 × 8 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does a 5850 N rating make one 16002 offer more durable than a 5590 N offer?
CZ lists Cr = 5850 N, while Global and NBK list 5590 N for their 16002 rows. The difference is real in the examined publications. It supports a conditional calculation, but no measured durability ranking or service-hour promise for your machine.
Four rows share the envelope, while their remaining fields differ.
Each manufacturer below lists d = 15 mm, D = 32 mm and B = 8 mm. Keep the rest of the row with its publisher when reviewing a quote.
One row lists open 16002, shielded 16002ZZ and sealed 16002-2RS.
Do not replace 5590 with 5850 in a Global or NBK quotation. The higher CZ dynamic figure accompanies CZ’s own row. The publications do not explain why the ratings differ, so this page does not attribute the difference to steel, manufacturing quality or an improved internal design.
A calculated ratio is useful only with its assumptions visible.
SKF’s bearing-selection explanation [5] gives the basic rating-life relationship L10 = (C/P)3 for ball bearings: C is basic dynamic rating and P equivalent dynamic bearing load. L10 is expressed in millions of revolutions at 90% reliability. This is background methodology, not a SKF performance result for CZ or NBK.
5850/5590 is about 1.0465: the displayed CZ dynamic rating is about 4.65% higher. If the same valid P is used in both basic calculations, their calculated life ratio is (5850/5590)3 ≈ 1.146. That is about 14.6% higher calculated basic rating life under that assumption. It is not a tested life increase and supplies no operating hours without the actual load and speed.
A supplier claiming a life benefit should show the offered bearing’s rating basis, the load calculation and the stated reliability and units. Do not treat an applied machine force as P without resolving how it reaches the bearing. Do not put the static rating Cor into the dynamic-life formula.
SKF also distinguishes calculated basic life from actual service life, which depends on lubrication, contamination, mounting and other conditions. This guide therefore does not apply a SKF life-modification factor to these manufacturers or claim that the ratio predicts field durability.
A “16002” price alone leaves the closure and speed claim open.
GOOT’s row distinguishes an open item from 16002ZZ and 16002-2RS while keeping an 8 mm width in its listed B and B1 fields. Sharing one published row is not proof that every closure can run at every displayed speed.
Ask GOOT to attach the speed condition to the actual offered suffix. Ask NBK whether its offer corresponds to the non-contact headings. Ask CZ which of the illustrated constructions its quotation supplies. If Global is selected, obtain its own speed document for that construction.
For the load claim, request one clear deliverable: a calculation tied to the full quoted designation, with actual bearing forces, equivalent-load basis, rotational duty, life units and relevant operating conditions. This separates an explainable selection from a sales statement based only on the largest Cr number.
The directory has six manufacturer records for the bare 16002 model. Four primary sources were freshly read for this guide; historical RCL and INYOUNG fields remain outside this fresh comparison. A separate Hongchi 16002ZZ record also exists. Its closure-specific order questions belong to that offer rather than being silently merged into the bare-model ratings.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Compare the recorded figures.
Property
Finding
Sources
Dynamic load rating
Ranges 5.59 – 5.6 kN across 3 sources
3
Static load rating
Ranges 2.83 – 2.86 kN across 3 sources
3
Limiting speed — grease
Ranges 20000 – 24000 rpm across 3 sources
3
Limiting speed — oil
Ranges 24000 – 28000 rpm across 3 sources
3
Reference mass
Ranges 0.023 – 0.027 kg across 2 sources
2
Where the figures differ, use the drawing from the manufacturer you buy from.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
8.5 mm
Mean diameter dm
(D + d) / 2
23.5 mm
C / C₀ load ratio (3 sources)
dynamic ÷ static load rating
RCL 1.95 · NBK 1.96 · INYOUNG 1.98
Arithmetic on the figures above — not a bearing life calculation for your load case.
CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.
Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs
72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
GOOT publishes miniature/small deep-groove and angular-contact bearings, including spindle and motor contexts. The metric table distinguishes open, ZZ and -2RS designations; confirm the current controlled specification and qualification instead of using older website content as a present delivery promise.
Published ranges: Deep groove ball bearings · Stainless steel and flanged variants · Angular contact ball bearings
6 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.
Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings
93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.
Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings
32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.
Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings
131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Global publishes ordinary shielded/sealed bearings alongside nonstandard steel and polymer pulley assemblies. Its scanned catalogue provides useful part-specific dimensions and construction examples; distinguish bore from shaft dimensions, match the complete assembly drawing, and confirm lubricant, noise testing and the current contracting entity.
Published ranges: Miniature and small bearings · Rubber-sealed bearing designs · Metal-shielded bearing designs
71 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Other designations with the same 15x32x8 mm envelope.
PDF page 91, printed page 89, text and rendered page read. Basic life definition, ball-bearing exponent and distinction from actual service life; background only.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies