BearingIndex
THE BEARINGINDEX DIRECTORY

16008 — 40 × 68 × 9 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 9 mmD = 68 mmd = 40 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16008

16008 is a deep groove ball designation documented on BearingIndex from 3 manufacturer publications. The published boundary dimensions are 40 × 68 × 9 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
40 mm
Outside D
68 mm
Width B
9 mm

Compare the 3 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Does a 40 mm shaft and 68 mm housing hole determine the fit of a 16008?

The nominal sizes leave the fit unresolved. NBK’s actual 16008 detail gives bore and outside-diameter tolerances. Combine those bearing-side ranges with the actual shaft and housing drawing limits before deciding whether the seat permits clearance, interference or both.

The diameter ranges are narrower statements than “40×68×9”.

NBK’s current 16008 specification panel [1] publishes:

NBK fieldNominal and published toleranceResulting diameter interval
Bore40 mm, +0 / −0.010 mm39.990–40.000 mm
Outside diameter68 mm, +0 / −0.011 mm67.989–68.000 mm

The intervals above are arithmetic from NBK’s published tolerances. They are not measurements of a delivered lot or specifications for CZ or INYOUNG. Ask NBK to confirm that these limits apply to the exact construction being quoted and identify the controlled specification behind them.

The same detail lists a 9 mm outer-ring width and a 0.3 mm fillet-radius entry. It does not give a width tolerance or a permissible machine-shoulder radius. Do not turn these two nominal entries into unstated assembly limits.

Use both ends of the seat tolerance, then assess the actual duty.

Obtain the shaft-seat limits Smin and Smax, and the housing-hole limits Hmin and Hmax, from the actual machine drawing. Using NBK’s published bearing diameter intervals, the dimensional screening is:

SeatSigned diametral-interference interval, mm
Shaft / bearing boreMinimum: Smin − 40.000
Maximum: Smax − 39.990
Bearing outside diameter / housing holeMinimum: 67.989 − Hmax
Maximum: 68.000 − Hmin

For this screening, a positive result means diametral interference and a negative result means diametral clearance. If an interval crosses zero, different allowed combinations can produce either. No shaft or housing limits have been supplied for your machine, so this page does not report an actual fit result.

These are endpoint calculations from dimensions, not predictions of ring deformation, mounted internal clearance, installation force or running temperature. Send the actual seat ranges, materials and load/thermal conditions to the manufacturer for assessment. Choosing a bearing-side tolerance or a seat fit by nominal diameter alone leaves those effects unresolved.

For receiving inspection, record the bearing measurements against the confirmed bearing specification and the seat measurements against the machine drawing. Passing either set separately does not establish that the combined fit is appropriate for the required duty.

An equal envelope does not share NBK’s tolerance specification.

CZ’s actual 16008 image row [2] also gives 40 / 68 / 9 mm. Its examined table publishes ratings, speeds and mass, but no diameter-tolerance limits. Do not insert NBK’s −0.010 / −0.011 mm into a CZ purchase specification without CZ’s confirmation.

INYOUNG’s corresponding source page displayed a maintenance notice when checked on 9 October 2026. Its historical directory record is not a newly verified tolerance or duty document. Obtain a current drawing if that offer is shortlisted.

NBK’s detail also offers customizable closure and ball-material options. Confirm the configuration and its applicable data together with the tolerance document. The outcome needed for this task is a selected supplier’s bearing specification joined to actual seat limits and operating requirements, rather than an unqualified “40 mm fit”.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
CZ
16008
—————2026-09-24 source ↗Request
NBK
16008
11.589.12900011000—2026-09-24 source ↗Request
INYOUNG
16008
12.510.28500110000.132026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingRanges 11.58 – 12.5 kN across 2 sources2
Static load ratingRanges 9.12 – 10.2 kN across 2 sources2
Limiting speed — greaseRanges 8500 – 9000 rpm across 2 sources2
Limiting speed — oilAll 2 sources publish 11000 rpm2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 214 mm
Mean diameter dm(D + d) / 254 mm
C / C₀ load ratio (2 sources)dynamic ÷ static load ratingNBK 1.27 · INYOUNG 1.23

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16008.

CZ

Ningbo, Zhejiang, China

Miniature motor bearings and inch series

CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.

Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs

72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask CZ about 16008

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16008

NBK

Ningbo, Zhejiang, China

Deep groove ball bearings and custom variants

NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.

Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings

32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask NBK about 16008

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
Brushless motorsCZ
DronesCZ
Garden toolsCZ
GeneratorsINYOUNG
MotorcyclesINYOUNG
Power toolsCZ

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 40x68x9 mm envelope.

DesignationBearing familyWorks
16008zzDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16008.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. CZ · 16008 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. NBK · 16008 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  3. INYOUNG · 16008 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. NBK · actual 16008 specification panel ↗

    Fresh loaded specification panel read: bore/OD nominal values and tolerances, outer width, fillet field and configurable construction. Diameter bounds and seat equations are arithmetic, not supplier fit approval or measured-lot evidence.

  2. CZ · actual 16008 catalogue-image row ↗

    Original image freshly opened and actually viewed with 16008 row and mm/N/rpm/kg headers. No tolerance columns in this sheet.

  3. INYOUNG · corresponding source currently under maintenance ↗

    Actual browser visit on 2026-10-09 displayed a site-maintenance notice, not a model table. Historical directory data is not freshly confirmed.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.