Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
16008zz
16008zz is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 40 × 68 × 9 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does the examined 16008ZZ page support an all-stainless, washable bearing?
It does not establish that construction. Hongchi lists GCr15 for both rings and the balls, while SPCC/SUS applies to the shields. A stainless shield option is not proof of stainless rings or a water-resistant complete assembly.
Separate the general material menu from the specific component table.
Hongchi’s actual 16008ZZ page [1] lists stainless steel, bearing steel and carbon steel as general material options. Its detailed component table is more specific:
Component
Examined entry
Procurement implication
Inner ring, outer ring and balls
GCr15
The table does not identify these parts as stainless.
ZZ shields
SPCC / SUS
An option applies to the shield; the selected material and grade remain to be specified.
Cage
SUS / MN
The slash entry does not identify one supplied cage material.
If the quotation says “stainless 16008ZZ”, require a declared material for each ring, the balls, cage and shields. Ask whether it is a separately offered construction and obtain its own controlled designation and specification. Do not extend “SUS” from the shield row to the rolling-contact parts.
The page also combines ZZ, RS, RZ and open options under one model description. A common 40 / 68 / 9 mm envelope does not resolve which closure and materials an offer contains. The examined photograph does not carry a model or batch identification and cannot settle those choices.
A metal shield is not evidence of a washable assembly.
SKF’s general sealing explanation [2] distinguishes a shield with a small gap from a contact seal. Shields suit relatively clean conditions or low-friction requirements; contact seals are commonly considered where water or moisture is present. This explains why closure type matters, but does not establish Hongchi’s exact shield geometry or approve any Hongchi variant for your cleaning process.
Describe the actual exposure: occasional condensation, splash, cleaning spray or immersion, together with fluid chemistry, temperature and pressure where applicable. Have the supplier identify what protects the complete bearing arrangement, including the housing and shaft-side ingress paths. A material declaration alone does not answer the ingress question.
If a sealed alternative is proposed, request its exact seal material, contact arrangement, lubricant compatibility and protection evidence for that exposure. Neither the generic RS option on this page nor a change of shield material establishes a washdown or chemical-cleaning capability.
The reference speed and grease fields still need their construction identified.
The source gives 57 under a grease heading marked ×1000 rpm: literally 57,000 rpm. It labels the neighbouring 70 entry only as lubricant, not oil. This page preserves that distinction; it does not correct the manufacturer’s figure or turn the second entry into an oil-lubricated limit.
Hongchi marks the table as reference data and asks buyers to consult it. Before using the grease figure for an offered ZZ or stainless variant, request confirmation of the exact construction, lubricant and load/temperature conditions supporting the intended duty. The −40 to 160 °C entry is not a documented simultaneous high-speed, wet-environment operating test.
The listed grease-fill range is 25–30%, without a defined percentage basis. Ask what volume or other basis it uses and which grease is actually supplied before writing an acceptance fill quantity. Do not convert it into grams or an instruction to add grease. Those confirmations belong to the same offered construction as the component-material and protection declarations.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
14 mm
Mean diameter dm
(D + d) / 2
54 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.
Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings
80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 40x68x9 mm envelope.
Fresh full page and actual photograph examined: general options versus specific component entries, 40/68/9 mm, grease heading multiplier, unnamed neighbouring lubricant field and a fill percentage with no stated basis. No supplied-batch declaration or wet-environment test inspected.
PDF page28 read, rendered and actually viewed. General shield/contact-seal distinction only; no SKF seal design, water rating or approval transferred to Hongchi.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies