BearingIndex
THE BEARINGINDEX DIRECTORY

16003E — 17 × 35 × 8 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 8 mmD = 35 mmd = 17 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16003E

16003E is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 17 × 35 × 8 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
17 mm
Outside D
35 mm
Width B
8 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Would replacing LYC 16003E with the wider 6003E buy more rated capacity?

In the examined LYC catalogue, both rows list C = 5.93 kN and C0 = 3.18 kN. The wider 6003E changes width and catalogue mass, but does not raise these published ratings. Choose the change by the assembly’s actual objective, not by width alone.

The two LYC rows change size without changing the listed load ratings.

LYC’s original table [1] places 16003E and 6003E in the same 17 mm bore group. Aligning the designation half with its dimensional half gives this comparison:

LYC catalogue field16003E6003E
Original designation7000103E103E
d / D / B17 / 35 / 8 mm17 / 35 / 10 mm
C / C05.93 / 3.18 kN5.93 / 3.18 kN
Grease / oil limiting speed19000 / 24000 r/min19000 / 24000 r/min
da minimum / Da maximum / ra maximum19 / 33 / 0.3 mm19 / 33 / 0.3 mm
Catalogue mass0.0311 kg0.0382 kg

The nominal width increases by 2 mm and the catalogue mass by 7.1 g. Those are arithmetic differences. The table supplies no higher C or C0 for 6003E, and no stiffness or assembled-temperature comparison. It does not establish that their internal construction is identical.

The matching bore and outside diameter also do not establish that the wider item fits the existing axial stack. The catalogue’s shoulder diagram uses da and Da for mating shoulders and ra for the mating corner limit; these do not replace the shaft/housing seat diameters.

Ask what the added width is supposed to solve.

If the problem is insufficient axial space
Moving from the nominal 8 mm 16003E to the 10 mm 6003E requires 2 mm more bearing width. Identify the available space and locating arrangement on the actual drawing; the proposed replacement does not create space.
If the problem is the locating stack
Show which inner- and outer-ring faces are located and which component closes the stack. The additional width must be incorporated into that drawing’s retention and tolerance chain. Do not treat the same 17/35 diameters as an axial fit approval.
If the problem is load capacity
Ask the selected supplier to assess the actual bearing loads and required life against the offered full designation. These two rows do not provide a published-rating increase with which to justify the wider replacement.
If the goal is stiffness or thermal behaviour
Request evidence for that property under the relevant assembly conditions. Width, weight and equal catalogue ratings do not provide a measured deflection or temperature result.

A justified substitution identifies the unmet requirement, supplies evidence addressing it and revises the actual assembly drawing where needed. If the only stated reason is “wider means stronger”, this catalogue comparison leaves that reason unsupported.

These are manufacturer-specific rows from the examined publication. Preserve E and any additional actual suffixes in the enquiry, and confirm the current drawing revision. The comparison does not transfer LYC’s values to another maker’s bare 16003 or 6003.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Source recorded
LYC
16003E
5.933.1819000240002026-09-23 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 29 mm
Mean diameter dm(D + d) / 226 mm
C / C₀ load ratiodynamic ÷ static load ratingLYC 1.86

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16003E.

LYC

Ball and roller bearings

LYC publishes a broad bearing portfolio. This sourcing guide separates catalogue selection, engineered applications and order-specific evidence.

49 designations documented here · source recorded 2026-10-07

Ask LYC about 16003E

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 17x35x8 mm envelope.

DesignationBearing familyWorks
16003Deep groove ball6

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16003E.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. LYC · 16003E source ↗

    Directory record dated 2026-09-23. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. LYC · actual 16003E and 6003E catalogue rows ↗

    PDF page 54, printed pages 101–102, both halves rendered and examined. The first two rows of the 17 mm group were aligned to their full designations; dimensions, ratings, speeds, mounting limits and mass read. No stiffness, thermal or assembly performance inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.