BearingIndex
THE BEARINGINDEX DIRECTORY

16006zz — 30 × 55 × 9 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 9 mmD = 55 mmd = 30 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16006zz

16006zz is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 30 × 55 × 9 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
30 mm
Outside D
55 mm
Width B
9 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Can 0.005–0.013 mm on the 16006ZZ page be used as a hot-running acceptance limit?

The examined Hongchi table does not establish that limit. Its clearance entry converts to 5–13 μm, but the page does not name the clearance direction, measurement load or whether the bearing is unmounted, mounted or operating. Resolve those definitions before writing a purchase or machine acceptance requirement.

The published 5–13 μm range needs a test definition.

Hongchi’s actual 16006zz page [1] gives the clearance column’s minimum as 0.005 mm and maximum as 0.013 mm. Multiplying by 1000 converts these to 5 and 13 μm. That conversion changes the unit only; it does not supply a test method or assign a clearance class.

The examined table calls the field “游隙” and does not say radial or axial. Ask Hongchi to specify the intended direction, bearing condition, measurement load, temperature and correction method. Record the agreed definition alongside the numeric limits in the inspection requirement.

Condition to distinguishWhat the evidence must identify
Incoming, unmounted bearingA supplier-agreed clearance measurement before installation, with its direction and method. Do not silently name the website’s range as this state.
Mounted, before operationThe actual shaft and housing fits, assembly condition and applicable residual-clearance requirement.
Operating at stable temperatureThe actual thermal and duty conditions and the permitted operating clearance or preload established for the assembly.

SKF’s execution chapter [2] distinguishes initial clearance before mounting, mounted clearance before operation, and operating clearance at stable temperature. It explains that interference fits and thermal expansion can change clearance. These definitions explain why the three states differ; they do not turn Hongchi’s unqualified numeric entry into an approved operating range.

A record labelled only “clearance passed” cannot show which requirement was checked. For an incoming lot, tie the result to the agreed measurement definition and lot identifier. A later mounted or thermal assessment is a separate result, even when the incoming measurement passes.

Select the offered construction and fits before assessing operating clearance.

The current page groups 16006zz, rs, rz and open variants together. It gives both OPEN and zz widths as 9 mm, with a 30 mm bore and 55 mm outside diameter. This is not a dimensional or clearance specification for every listed closure variant.

For the exact offered ZZ construction, send the actual shaft-seat and housing-seat tolerance ranges, component materials, locating arrangement and duty temperatures to the manufacturer. Ask it to identify the required incoming clearance and the resulting mounted/operating condition. The website gives no shaft/housing fit class or approved reduction calculation for your assembly.

Do not rename 5–13 μm as C3, or change to a larger clearance group solely because the assembly is expected to run warm. The correct clearance must be assessed with the actual fits and thermal conditions. The examined page does not identify a clearance group for this model.

Hongchi also publishes 9950 N dynamic and 6530 N static ratings. Its grease speed entry is 43 under a ×1000 rpm header, meaning 43,000 rpm; the adjacent row is labelled “润滑剂”, not explicitly oil. These entries do not state the clearance used in a qualifying test. Neither the speed figure nor the page’s −40~160°C temperature entry establishes a tested operating point for the assembly.

The parts table names GCr15 for rings and balls, while shield and cage fields retain material alternatives. Resolve those alternatives and the lubricant in the actual quotation. A usable order joins an exact construction to a defined clearance measurement and an assessed mounting/duty condition; it does not copy one undecided range into every inspection stage.

What each manufacturer published.

ManufacturerSource recorded
Hongchi
16006zz
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 212.5 mm
Mean diameter dm(D + d) / 242.5 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16006zz.

Hongchi

Ningbo, Zhejiang, China

Miniature metric, inch and thrust bearings

Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.

Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings

80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Hongchi about 16006zz

Applications the publishing works state.

ApplicationStated by
Cooling fansHongchi
DronesHongchi
Miniature motorsHongchi
Precision instrumentsHongchi

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 30x55x9 mm envelope.

DesignationBearing familyWorks
16006Deep groove ball5

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16006zz.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Hongchi · 16006zz source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Hongchi · actual 16006zz parameter tables ↗

    Fresh complete text read: 30/55/9, OPEN/zz widths, 0.005–0.013 mm clearance with unnamed direction/state, material alternatives, N rating and ×1000 rpm headers. Embedded generic structure drawing viewed; no current model photo or clearance-class proof.

  2. SKF · initial, mounted and operating clearance ↗

    PDF pages 184–186, printed 182–184; definitions/fit-temperature explanation read, pages 184 and 185 rendered and viewed. No SKF clearance-class limits, fit factors or operating recommendation transferred to Hongchi.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.