BearingIndex
THE BEARINGINDEX DIRECTORY

16011 — 55 × 90 × 11 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 11 mmD = 90 mmd = 55 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16011

16011 is a deep groove ball designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 55 × 90 × 11 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
55 mm
Outside D
90 mm
Width B
11 mm

Compare the 2 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Which ZWZ inclination entry applies to the offered 16011 clearance class?

ZWZ’s deep-groove series page lists 8′ for the basic clearance class,12′ for class 3 and16′ for class 4. The specific 16011 dimensional row does not identify a delivered clearance class. The largest series entry therefore does not define the supplied item’s permitted alignment.

The series table ties each angle to a clearance class.

ZWZ’s actual Allowable angle error table [1] provides the following class-dependent entries. The prime symbol ′ denotes minutes of arc; dividing by 60 gives degrees.

ZWZ table classPublished angleUnit conversion only
Basic class8′Approximately 0.133°
Class 312′0.200°
Class 416′Approximately 0.267°

The degree values are arithmetic conversions, not additional operating allowances. Keep the angle unit in the drawing and supplier assessment so a number without its prime symbol cannot be read as degrees.

ZWZ’s radial-clearance tab lists class 2, standard (N),3,4 and5. Its suffix explanation states that C3 is greater than normal clearance and C4 greater than C3. The catalogue’s plain 16011 row gives 55/90/11 mm but does not identify which class a particular quotation supplies. Request the complete designation and agreed clearance range before choosing the corresponding table row.

Selecting a larger clearance class does not repair the shaft and housing alignment.

Describe the actual alignment condition to ZWZ: the shaft and housing geometry, the measured or calculated relative ring inclination, and any relevant change under load or temperature. Have the manufacturer assess that condition for the exact 16011 construction and selected clearance. No measured machine angle is supplied here, so this page does not report a passed installation.

Do not change an order to C3 or C4 solely to obtain a larger angle number. That changes the clearance specification as well. The fit and thermal conditions still need to leave the intended operating clearance; the selected bearing must also meet the machine’s running requirements.

SKF’s independent deep-groove guidance [2] notes that misalignment can increase bearing noise and reduce service life. Its own numerical angle range is not substituted for ZWZ’s table. A series allowance should not be treated as a promise of unchanged noise or life at your actual duty.

The mounting row is another separate drawing check: ZWZ gives da min 60.6 mm, Da max 84.4 mm and ra max 0.6 mm. Meeting those shoulder bounds does not prove the shaft and housing axes are aligned. Record the support geometry and alignment assessment together rather than using the nominal envelope as evidence for both.

The reviewed fields do not constitute a combined operating approval.

The exact ZWZ row gives basic ratings Cr 18.6 kN and Cor 15.2 kN, plus reference mass 0.255 kg. Its grease and oil entries are 8000 and 9600, but the speed-unit heading is malformed: r with subscript min. This page retains those raw entries with notes and requests confirmation rather than asserting a newly verified rpm unit.

The operating-temperature tab says the standard series must not exceed 120 °C and is also affected by lubricants, with advice required above that temperature. It does not validate simultaneous operation at that temperature, the largest inclination entry and the largest listed load or speed. Obtain the assessment for the actual combination.

The comparison table also retains an older INYOUNG 16011 record. Its current source could not be re-read in this review. ZWZ’s clearance/angle table, mounting bounds and temperature statement must not be assigned to that supplier’s bearing.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Grease speed column — see source notesOil speed column — see source notesMinimum corner radius (mm)Reference mass (kg)Source recorded
ZWZ
16011
18.615.28000
ZWZ’s heading renders r with a subscript min, rather than an unambiguous r/min unit. The raw grease entry is 8000; confirm the intended unit and offered operating basis.
9600
ZWZ’s heading renders r with a subscript min; the raw oil entry is 9600. This review does not turn the malformed unit heading into a confirmed rpm claim.
0.60.2552026-10-07 source ↗Request
INYOUNG
16011
16.2
Historical INYOUNG record; the current source could not be re-read during this review.
17.2
Historical INYOUNG record; not newly verified against a current accessible specification.
6300
Historical INYOUNG record interpreted as rpm; not reverified for a current offered construction.
8000
Historical INYOUNG record interpreted as rpm; current offered basis not reverified.
—0.262026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingRanges 16.2 – 18.6 kN across 2 sources2
Static load ratingRanges 15.2 – 17.2 kN across 2 sources2
Reference massRanges 0.255 – 0.26 kg across 2 sources2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 217.5 mm
Mean diameter dm(D + d) / 272.5 mm
C / C₀ load ratio (2 sources)dynamic ÷ static load ratingZWZ 1.22 · INYOUNG 0.94

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16011.

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16011

ZWZ

Ball, roller and slewing bearings

Actual taper-bearing suffix/height examples, three-row slewing interface boundaries, group-versus-shareholding entity evidence and the manufacturer’s preliminary/正式 channel authorization distinction.

12 designations documented here · source recorded 2026-10-08

Ask ZWZ about 16011

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
GeneratorsINYOUNG
MotorcyclesINYOUNG

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 55x90x11 mm envelope.

DesignationBearing familyWorks
16011zzDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16011.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. ZWZ · 16011 source ↗

    Directory record dated 2026-10-07. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. INYOUNG · 16011 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZWZ · 16011 exact search result and technical tabs ↗

    Actual part-number search returned the independent 16011 row; DOM and screenshot examined. Allowable angle error, radial clearance and temperature tabs read after their headings matched the selected content; code descriptions separately read. Series entries are not a delivered-batch or machine approval.

  2. SKF · Rolling bearings 17000, deep-groove bearing data, printed page 250 ↗

    PDF page 252 read, rendered and actually viewed. Misalignment effect on noise/life used as general background; SKF numerical angle limits, clearance choices and tolerance values are not transferred to ZWZ.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.