Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
16002zz
16002zz is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 15 × 32 × 8 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does Hongchi’s 16002ZZ table qualify a hot, high-speed bearing?
The page supplies a grease-speed number, a temperature range and a grease percentage, but does not define a combined operating test. Keep those separate: a quote must identify the actual ZZ construction and explain the conditions behind each claim before it can answer your duty requirement.
The page title identifies ZZ; the parameter row covers more constructions.
Hongchi’s exact product page [1] is titled 16002zz, while its model field reads “16002zz/rs/rz/开式”. It lists 15 mm bore and 32 mm outside diameter, with separate OPEN and ZZ width entries both equal to 8 mm. That does not make every item named in the combined model field the same order.
State ZZ explicitly in the quotation and request the offered closure drawing. The material-options field names stainless steel, bearing steel and carbon steel; a separate component table names GCr15 for rings and balls, SPCC/SUS for the shield and SUS/MN for the cage. It does not assign every alternative to the offered batch. A stainless shield option is not proof of stainless rings.
Both parameter tables carry the qualification that their data is for reference and selection should be discussed with “宏诚精密”. The site identifies itself as Hongchi / 宏驰. Ask the supplier to issue the order’s technical document under the actual supplying entity, with a resolved material and construction list. The product images did not load successfully during this review, so this guide makes no visual construction claim from them.
Treat speed, temperature and grease quantity as three separate questions.
Grease speed: 50 beneath “×1000 rpm”
The displayed arithmetic is 50,000 rpm. The examined table does not define the load, clearance, exact grease, duration or thermal conditions for that figure. Ask which selected construction it covers and request its duty basis. The adjacent entry is labelled “润滑剂” and displays 53 under the same speed unit; this guide does not silently rename that ambiguous label as oil lubrication.
Temperature: −40 to 160°C
The “耐高温” row follows the SRL grease entry. Ask whether the range describes the lubricant, a component or a qualified assembled bearing, and whether its endpoints are continuous or conditional. The page does not establish simultaneous continuous operation at the published speed and upper temperature.
Grease percentage: 25–30%
The first table says “油脂率” without defining the reference volume or measurement method. Ask what the percentage measures, the selected lubricant’s precise designation and how supplied quantity is controlled. Do not convert it into a filling mass from an undefined denominator.
GOOT’s separate 16002 family row [2] displays grease/oil values of 24000/28000 rpm and separately names open, ZZ and 2RS items. Those numbers belong to GOOT. They neither qualify Hongchi’s offer nor prove Hongchi’s 50,000 figure wrong: the compared publications do not establish identical conditions.
For a hot, high-speed enquiry, put the required rpm, forces, temperature location and duration together in one duty statement. Request confirmation against the offered ZZ configuration with the three field definitions above. Separate catalogue maxima cannot substitute for that combined assessment.
The listed 5–13 μm needs a measurement state.
Hongchi lists minimum and maximum clearance as 0.005 and 0.013 mm: 5 and 13 μm by unit conversion. It also lists Cr = 5590 N and Cor = 2840 N. Neither rating identifies the measurement state of the clearance interval.
Ask whether the clearance entry is radial internal clearance of the unmounted item, how it is measured and which complete offered designation it applies to. Do not label it an ISO clearance group from this interval alone, or treat it as the residual clearance after fitting and heating in your assembly.
The useful receiving document for this order should connect the exact suffix and materials to the selected grease, defined quantity and clearance measurement. A separately documented speed/temperature assessment should address the actual duty. If those definitions remain unanswered, the page has supplied reference data rather than a verified operating approval.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
8.5 mm
Mean diameter dm
(D + d) / 2
23.5 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.
Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings
80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 15x32x8 mm envelope.
Both actual parameter tables read: dimensions, construction options, materials, clearance, grease, temperature and speed headings. Reference-only footnotes and ambiguous labels retained; product images failed to load.
Freshly read open/ZZ/2RS designations and grease/oil speeds. Different manufacturer; no transfer of operating approval to Hongchi.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies