Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
16003
16003 is a deep groove ball designation documented on BearingIndex from 6 manufacturer publications. The published boundary dimensions are 17 × 35 × 8 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
A 16003 bearing has a 17 mm bore. Why does “03 × 5” give the wrong order?
The examined manufacturer rows identify 16003 as 17×35×8 mm. The small-bore code 03 is an exception to the familiar multiply-by-five shortcut. If a drawing says 15 mm while the order says 16003, resolve that contradiction before purchase.
The small-bore codes have their own lookup.
LYC’s published bore-code explanation [1], table 2.3, maps 00, 01, 02 and 03 to nominal bores of 10, 12, 15 and 17 mm. Its divide-by-five scheme applies to the stated larger-bore range with additional exceptions; it is not the rule for these four codes.
Therefore, multiplying the “03” in 16003 by five produces 15 mm, but not the bore of the examined 16003. The current NBK row [2] and GOOT row [3] explicitly give 17 mm. Use the exact manufacturer row and drawing to resolve the item, rather than extending a shortcut outside its defined range.
The prefix and series digits are not a direct millimetre measurement either. The code explanation is a way to read a designation; it does not specify the offered bearing’s fits, clearance or operating capacity.
Changing 16003 to 16002 also changes the outside diameter.
The bore is 15 mm, and the outside diameter is 32 mm.
16003: 17 × 35 × 8 mm
The bore increases to 17 mm and the outside diameter to 35 mm; the nominal width remains 8 mm.
16004: 20 × 42 × 8 mm
This row has a 20 mm bore and 42 mm outside diameter. Its shared width does not make it suitable for the 16003 housing.
Global’s actual metric 16003 row [5] also lists 17/35/8 mm. These fresh checks establish the nominal envelope, not an interchangeable construction across all publishers.
If the assembly drawing calls for a 15 mm bore but the order names 16003, replacing the name with 16002 is not a complete correction: review the outside diameter and locating geometry too. If the shaft is nominally 17 mm, that alone does not select 16003; the housing, axial space and actual duty must also match the selected design.
Keep the model and all three nominal dimensions on the same drawing revision. Do not propose a sleeve, altered shaft or changed seat merely to reconcile a transcription error; first identify which item the assembly was designed to use.
A corrected bore code still leaves the closure to specify.
GOOT’s examined row distinguishes open 16003, shielded 16003ZZ and sealed 16003-2RS, with B and B1 both shown as 8 mm. Resolve the full closure designation in the quote. A correct 17 mm bore does not by itself identify the item’s sealing, lubricant or clearance.
Send the old complete marking and current assembly drawing to the selected manufacturer. Ask it to confirm the model/dimension pair, actual closure, drawing revision and mounting requirements. If the original record and drawing disagree, retain the corrected revision in the purchasing record so the same error is not repeated on the next order.
This directory has six manufacturer records for the bare model. The four dimension sources cited here were freshly examined. INYOUNG’s current linked page was blocked by a certificate error during this review, and RCL’s current series page supplied no readable 16003 row. Their historical ratings are not treated as newly verified by this guide.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Compare the recorded figures.
Property
Finding
Sources
Dynamic load rating
Ranges 6 – 6.8 kN across 3 sources
3
Static load rating
Ranges 3.26 – 3.35 kN across 3 sources
3
Limiting speed — grease
Ranges 18000 – 22000 rpm across 3 sources
3
Limiting speed — oil
Ranges 22000 – 26000 rpm across 3 sources
3
Reference mass
Ranges 0.027 – 0.028 kg across 2 sources
2
Where the figures differ, use the drawing from the manufacturer you buy from.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
9 mm
Mean diameter dm
(D + d) / 2
26 mm
C / C₀ load ratio (3 sources)
dynamic ÷ static load rating
RCL 1.83 · NBK 1.84 · INYOUNG 2.03
Arithmetic on the figures above — not a bearing life calculation for your load case.
CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.
Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs
72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
GOOT publishes miniature/small deep-groove and angular-contact bearings, including spindle and motor contexts. The metric table distinguishes open, ZZ and -2RS designations; confirm the current controlled specification and qualification instead of using older website content as a present delivery promise.
Published ranges: Deep groove ball bearings · Stainless steel and flanged variants · Angular contact ball bearings
6 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.
Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings
93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.
Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings
32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.
Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings
131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Global publishes ordinary shielded/sealed bearings alongside nonstandard steel and polymer pulley assemblies. Its scanned catalogue provides useful part-specific dimensions and construction examples; distinguish bore from shaft dimensions, match the complete assembly drawing, and confirm lubricant, noise testing and the current contracting entity.
Published ranges: Miniature and small bearings · Rubber-sealed bearing designs · Metal-shielded bearing designs
71 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Other designations with the same 17x35x8 mm envelope.
PDF page 6, printed page 6, original text and rendered spread read. Manufacturer explanation of 00/01/02/03 exceptions; not a claim to reproduce the latest full national standard.
Rendered PDF page 7, printed page 11, exact 17/35/8 row viewed. Not a cross-manufacturer equivalence certificate.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies