Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
16011zz
16011zz is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 55 × 90 × 11 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does Hongchi’s 60 × 1000 rpm entry actually cover the quoted 16011ZZ?
The speed entry is real: Hongchi prints 60 under grease with a ×1000 rpm heading. Multiplication gives 60,000 rpm. The page also groups ZZ, RS, RZ and open constructions without assigning that speed to a particular one. The missing link is the execution and operating basis, not the arithmetic.
The number is published; the offered execution is not tied to it.
Several executions share this page; the title alone does not allocate every property to ZZ.
Boundary dimensions
55 mm bore, 90 mm outside; OPEN width 11 mm and ZZ width 11 mm
Open and ZZ widths are explicit. Separate RS/RZ width cells are not supplied.
Grease speed row
60, with ×1000 rpm heading
60,000 rpm is a unit conversion. A ZZ-specific operating limit still needs its basis.
Adjacent speed row
76, labelled 润滑剂 — lubricant
Do not rename this an oil-speed approval; the lubricant and execution are unspecified.
The source expressly calls its table reference information and asks the buyer to consult the supplier when selecting. This review neither silently corrects 60 to a more plausible-looking number nor treats the raw entry as a guarantee. Ask Hongchi to identify the controlled specification revision, exact execution and conditions supporting the quoted speed.
A grease label does not establish thermal and mechanical suitability.
SKF’s published speed guidance [2] distinguishes reference speed based on thermal conditions from limiting speed based on mechanical constraints. This explains why the type of speed figure matters; it does not classify Hongchi’s entry as either one or transfer SKF’s reference conditions to it.
For this offer, request two linked answers: which bearing execution the manufacturer assessed, and what operating conditions its speed statement covers. Cage strength and stability, shield or seal construction and lubrication matter to the mechanical assessment. Actual load, lubricant, frictional heat, neighbouring heat sources and heat dissipation matter to the temperature assessment.
Hongchi names SRL grease, a 25–30% grease rate and −40 to 160 °C on the same page. It does not define the percentage basis or a combined speed/load/temperature duty. Those fields cannot establish that the supplied ZZ bearing runs continuously at 60,000 rpm and 160 °C. Define continuous speed, short peaks and their durations separately; submit the actual operating load and cooling arrangement instead of combining independent catalogue maxima.
If the manufacturer proposes a different cage, lubricant or closure to meet the duty, retain that change in the full ordered designation and drawing revision. An assessment for the changed bearing cannot be attached to an unchanged generic ZZ quotation.
Turn a speed claim into evidence attached to the purchased item.
The page lists SPCC/SUS shield material and SUS/MN cage entries; it does not select the delivered combination. Ask the supplier to identify those components, grease specification and fill basis in the controlled execution supporting its speed answer. A metal-shield product photograph cannot establish the hidden cage, grease or speed qualification.
Where the supplier supports the offer with a test report, match its bearing designation and construction to the quotation. Read the actual speed, load, duration, lubrication, temperature measurement location and cooling arrangement. Distinguish a short run from continuous operation and a sample result from a stated production acceptance criterion. Agree temperature and vibration criteria for the intended machine; this page invents neither limits nor test results.
If the only answer repeats “60 ×1000 rpm” from the mixed-variant web table, the arithmetic is settled but the execution-specific duty remains unresolved. Obtain a supported operating assessment, revise the duty with the machine designer, or compare another bearing with evidence for the same conditions. The 55/90/11 mm envelope alone is insufficient grounds to release this speed requirement.
The source also publishes Cr 19,300 N and Cor 16,300 N. They are basic ratings, not the load actually applied in a speed test. The site’s historical record currently contains only boundary dimensions; these newly reviewed fields and their limitations are documented here without assigning a speed limit to every variant.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
17.5 mm
Mean diameter dm
(D + d) / 2
72.5 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.
Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings
80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 55x90x11 mm envelope.
Exact model page and both tables read in browser; actual product and speed-table screenshots viewed. Mixed variant field, explicit OPEN/ZZ widths, grease 60 ×1000 rpm, lubricant-labelled 76 and reference-only warning retained. No delivered execution or speed-test result established.
PDF page 137 read, rendered and actually viewed. Thermal-reference versus mechanical-limit distinction used as technical background; SKF speed values, friction model and standardized operating conditions are not assigned to Hongchi.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies