BearingIndex
THE BEARINGINDEX DIRECTORY

16002E — 15 × 32 × 8 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 8 mmD = 32 mmd = 15 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16002E

16002E is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 15 × 32 × 8 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
15 mm
Outside D
32 mm
Width B
8 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Your spare-parts list says 7000102E. Is a bare 16002 quotation complete?

LYC’s catalogue places present designation 16002E and original designation 7000102E on the same row. Preserve that manufacturer-specific mapping in the enquiry. A quotation that drops E still needs its design identity and mounting drawing resolved; matching the three nominal dimensions does not answer that question.

Use the original-designation column to resolve the spare-part name.

LYC’s original catalogue [1], printed pages 101–102, identifies 16002E as the present designation and 7000102E as the original designation. Its row gives d = 15 mm, D = 32 mm and B = 8 mm. Keep the old marking and this exact catalogue mapping together when contacting the supplier.

If an offer reads only “16002”, ask the supplier whether it supplies LYC 16002E or a separately defined design from another manufacturer. Request the full item designation and drawing rather than changing the old purchasing record to the shorter name. The catalogue mapping proves what LYC calls this item; it is not a cross-manufacturer interchange certificate.

LYC’s designation explanation [2] places A, B, C, D and E in its internal-design code group and says the design contents depend on bearing structure. It does not give a specific construction definition for this 16002E row. This guide therefore does not label it a universal reinforced design or infer its ball count.

Seals, shields and external designs are described in a separate code group. E alone does not order a double shield or two rubber seals. Obtain the actual closure and all required supplementary codes for the quoted item.

The 15/32/8 envelope leaves three mounting limits to check.

The catalogue’s adjoining mounting diagram defines da, Da and ra. The 16002E row supplies these specific limits:

da minimum: 17 mm
Check the shaft-side shoulder diameter identified by da against this lower bound. It is a shoulder dimension in the diagram, not a new shaft-seat diameter replacing the 15 mm bore.
Da maximum: 30 mm
Check the housing-side shoulder dimension identified by Da against this upper bound. It does not replace the 32 mm outside diameter or prescribe a housing-seat fit.
ra maximum: 0.3 mm
Check the mating corner radius indicated by ra. The bearing boundary table separately lists r minimum = 0.3 mm. These are distinct symbols and bound directions, even though their displayed numbers match.

Put the seat diameters, shoulder dimensions and corner limits on the assembly drawing under their own symbols. Verify the axial locating faces as well. A purchase drawing showing only 15/32/8 leaves the mounting review incomplete.

The row supplies nominal dimensions and mounting bounds, not selected interference fits or the assembly’s residual internal clearance. Obtain those requirements for the actual shaft, housing and duty instead of deriving them from the shoulder numbers.

Keep the ratings with this designation and the actual lubrication arrangement.

The same LYC row publishes C = 5.48 kN, C0 = 2.8 kN, limiting speeds of 19800 r/min with grease and 25000 with oil, and mass 0.0274 kg. These values belong to the examined 16002E row. The catalogue does not supply a service-life result for your machine.

Ask the supplier to confirm the current full designation and drawing revision, particularly when quoting against an older spare-parts list. If a newer rating or construction is offered, retain the newer document and resolve its relation to the legacy item; do not combine newer ratings with an older mounting row by assumption.

A grease-lubricated assembly cannot use the oil column merely because it is larger. Confirm the offered closure, lubricant, loads and thermal conditions against the required speed. The next procurement document should identify the replacement design, show the checked shoulder geometry and state the duty basis.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Source recorded
LYC
16002E
5.482.819800250002026-09-23 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 28.5 mm
Mean diameter dm(D + d) / 223.5 mm
C / C₀ load ratiodynamic ÷ static load ratingLYC 1.96

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16002E.

LYC

Ball and roller bearings

LYC publishes a broad bearing portfolio. This sourcing guide separates catalogue selection, engineered applications and order-specific evidence.

49 designations documented here · source recorded 2026-10-07

Ask LYC about 16002E

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 15x32x8 mm envelope.

DesignationBearing familyWorks
16002Deep groove ball6
16002zzDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16002E.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. LYC · 16002E source ↗

    Directory record dated 2026-09-23. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. LYC · 16002E present/original designation and dimensional row ↗

    PDF page 54, printed pages 101–102, both halves rendered and read; exact 16002E/7000102E row aligned with dimensions, ratings, speeds, mounting bounds and mass.

  2. LYC · internal-design and external-design suffix explanation ↗

    PDF page 7, printed pages 7–8, text and rendered page examined. E grouped under internal design without a model-specific definition; seals and shields listed separately.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.