BearingIndex
THE BEARINGINDEX DIRECTORY

16010 — 50 × 80 × 10 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 10 mmD = 80 mmd = 50 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16010

16010 is a deep groove ball designation documented on BearingIndex from 3 manufacturer publications. The published boundary dimensions are 50 × 80 × 10 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
50 mm
Outside D
80 mm
Width B
10 mm

Compare the 3 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

What should a precision inspection report for the offered 16010 actually establish?

NBK’s page lists ABEC 3 as customizable and gives bore/OD tolerances. Those are specification entries, not measured results for the bearing being shipped. Identify the selected construction and the exact inspection characteristics before accepting a precision claim.

A diameter entry and a running-accuracy result are different evidence.

NBK’s exact 16010 specification [1] gives bore 50 mm with +0 / −0.010 mm and outside diameter 80 mm with +0 / −0.013 mm. Arithmetic on these entries gives reported intervals of 49.990–50.000 mm and 79.987–80.000 mm respectively. The page names outer-ring width 10 mm without a width-tolerance entry.

Those intervals do not identify every required measurement characteristic. SKF’s tolerance explanation [2] distinguishes dimensional and geometrical tolerances; its definitions separate a two-point bore size in a cross-section, size variation across sections and radial run-out of an assembled bearing. A measured diameter within an interval is not evidence that all of those characteristics pass.

For an NBK offer, ask which size characteristic its published bore/OD limits describe and which standard and edition define the selected class. Then specify the other characteristics required by the assembly drawing—such as relevant size variation, ring-width limits or assembled running accuracy—using agreed methods and limits. This page does not import SKF numerical tolerances or equate an ABEC label to a different supplier’s class.

The website lists ABEC 3 as customizable. Put the class actually selected in the order and inspection specification; the website option does not certify the shipped batch. If a different class is offered, obtain its complete applicable requirements rather than changing only the class name on the quotation.

The manufacturing flow shows an inspection stage, not its results.

NBK’s published manufacturing diagram [3] shows ring grinding and superfinishing, followed at assembly level by washing, inspection and rust prevention. It is a general process illustration. It does not show a 16010 lot number, measurement limits, instruments or actual results.

A reviewable delivery report should connect the delivered lot and complete designation to the agreed inspection specification. For each required characteristic, it should identify the measurement method and acceptance limit, report the result and make clear whether it represents the inspected pieces or a sampling decision. Include the actual inspection scope and traceability rather than treating a process-flow label as proof that every bearing was measured.

If the order selects ceramic balls or a particular closure from NBK’s customizable options, the report and controlled designation must refer to that same construction. A report for a steel-ball/open sample does not identify a different offered configuration. No batch results were supplied for this page, so it reports neither a precision pass nor a rejected lot.

The shared 50/80/10 mm envelope does not transfer NBK’s tolerance entries.

CZ’s independently examined 16010 image row [4] also gives 50/80/10 mm. It publishes Cr 16090 N, Cor 13150 N, grease 8500 rpm, oil 10000 rpm and mass 0.180 kg, but no corresponding bore/OD tolerance columns. Those load and speed entries do not establish the NBK tolerance requirements for a CZ offer.

The comparison table retains a historical INYOUNG record. Its source could not be re-read during this review, so the retained values are not presented as newly verified construction or precision evidence. Obtain a current specification and the agreed inspection basis from the manufacturer actually supplying the bearing.

Keep fit selection separate from bearing inspection: actual shaft and housing limits still need coordination with the offered bearing. The bearing/seat tolerance review explains that distinction; its model-specific numbers must not be substituted for this 16010 or for a CZ or INYOUNG tolerance that has not been supplied.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
CZ
16010
16.0913.158500100000.182026-09-24 source ↗Request
NBK
16010
16.113.174008800—2026-09-24 source ↗Request
INYOUNG
16010
16.2
Historical INYOUNG record; the current source could not be re-read in this review. This is not a newly verified offered rating.
13.2
Historical INYOUNG record; not reverified against a current accessible source in this review.
7000
Historical INYOUNG entry; current construction and operating basis remain to be confirmed.
9000
Historical INYOUNG entry; not a newly verified operating limit for an offered batch.
0.182026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingRanges 16.09 – 16.2 kN across 3 sources3
Static load ratingRanges 13.1 – 13.2 kN across 3 sources3
Limiting speed — greaseRanges 7000 – 8500 rpm across 3 sources3
Limiting speed — oilRanges 8800 – 10000 rpm across 3 sources3
Reference massAll 2 sources publish 0.18 kg2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 215 mm
Mean diameter dm(D + d) / 265 mm
C / C₀ load ratio (3 sources)dynamic ÷ static load ratingCZ 1.22 · NBK 1.23 · INYOUNG 1.23

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16010.

CZ

Ningbo, Zhejiang, China

Miniature motor bearings and inch series

CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.

Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs

72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask CZ about 16010

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16010

NBK

Ningbo, Zhejiang, China

Deep groove ball bearings and custom variants

NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.

Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings

32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask NBK about 16010

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
Brushless motorsCZ
DronesCZ
Garden toolsCZ
GeneratorsINYOUNG
MotorcyclesINYOUNG
Power toolsCZ

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 50x80x10 mm envelope.

DesignationBearing familyWorks
S16010ZZ/2RSDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16010.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. CZ · 16010 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. NBK · 16010 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  3. INYOUNG · 16010 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. NBK · exact 16010 specification ↗

    Fresh detail fully loaded and read: selected-class option, bore/OD limits, outer-ring nominal width and customizable construction. No lot-specific report or complete measurement-characteristic definition inspected.

  2. SKF · Rolling bearings 17000, printed pages 36 and 49 ↗

    PDF pages 38 and 51 read, rendered and actually viewed. General dimensional/geometrical and size/run-out distinctions only; no SKF class limits or ABEC-to-ISO equivalence transferred to NBK.

  3. NBK · manufacturing process diagram ↗

    Actual 2560×1969 diagram opened and browser screenshot viewed. General grinding/superfinishing and assembly washing/inspection/rust-prevention stages; not a 16010 batch inspection record.

  4. CZ · actual16010 row in the 16000-series image ↗

    Source image freshly viewed, exact 16010 row and headers checked. Five previously missing site-record fields individually supplemented with N-to-kN conversion; no tolerance-class proof inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.