Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball
16001
16001 is a deep groove ball designation documented on BearingIndex from 6 manufacturer publications. The published boundary dimensions are 12 × 28 × 7 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Can a 16001 recover 1 mm of axial space in a 6001 bearing seat?
Global lists the same 12 mm bore and 28 mm outside diameter for both models, but widths of 7 mm for 16001 and 8 mm for 6001. That identifies an axial drawing change. It does not establish that the existing shaft, housing and retention arrangement can use the narrower bearing unchanged.
One manufacturer’s catalogue shows exactly what becomes narrower.
The matching dynamic rating and ball complement do not fill the missing speed field or specify either offered bearing’s clearance, closure and lubricant. The 10 N static-rating difference is a published-row difference, not a measured improvement in your machine.
Use the table to identify the replacement question: the nominal width decreases by 1 mm. The minimum bearing chamfer is not a complete shaft/housing shoulder specification; request the selected bearing’s mounting-dimension drawing.
Locate the millimetre on the assembly drawing before choosing a retainer.
Start with the face that actually establishes the bearing’s axial position. In a drawing scenario where one bearing face stays against the same fixed shoulder, reducing the nominal width from 8 to 7 mm moves the opposite face 1 mm toward that shoulder. Any component that previously contacted the opposite face must be assessed against its new position.
A different drawing scenario holds the bearing’s mid-plane in the same position. Its two nominal faces would each move inward by 0.5 mm. That arithmetic depends on the mid-plane constraint; it is not evidence that the existing housing positions the bearing that way.
Mark the actual inner-ring and outer-ring locating faces, the retaining component and the dimension chain that closes against them. Ask the designer to resolve contact and retention at the new width, including the tolerances of the selected parts. Do not prescribe a 1 mm shim from the nominal difference alone: a shim’s location, contact face and resulting stack all need a drawing.
If the purpose is simply to free axial space, explain which neighbouring component needs that space. If the existing retention requires the original 8 mm stack, the narrower item has not yet solved that constraint. A useful quotation therefore includes the offered bearing drawing and a reviewed assembly revision, not just “same ID and OD”.
NBK supplies a speed row; it does not supply Global’s missing value.
NBK’s actual 16001 row [3] lists 24000 rpm with grease and 28000 rpm with oil. Both column headings explicitly state non-contact. Its dimensions are 12/28/7 mm and ratings 5110/2390 N.
For an NBK quotation, identify whether the offered closure and lubrication correspond to those headings before evaluating the actual rotational duty. Those numbers do not qualify an unspecified contact-sealed variant. For a Global quotation, request Global’s speed evidence for the selected construction: its examined 16001 table does not publish a speed.
The directory currently has six manufacturer records for 16001. This guide freshly verifies Global and NBK. RCL’s current 16-series page describes reduced width but supplies no readable 16001 parameter row in the examined page; its historical directory values are not treated here as a fresh confirmation. The remaining manufacturers need their own current drawing and duty evidence before an offer can be assessed.
The practical decision has two unresolved parts: confirm how the 7 mm width is retained in the actual assembly, and obtain duty evidence for the chosen supplier’s complete designation. Resolving only one does not approve the replacement.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Compare the recorded figures.
Property
Finding
Sources
Dynamic load rating
Ranges 5.09 – 5.11 kN across 3 sources
3
Static load rating
Ranges 2.36 – 2.39 kN across 3 sources
3
Limiting speed — grease
Ranges 24000 – 28000 rpm across 3 sources
3
Limiting speed — oil
Ranges 28000 – 32000 rpm across 3 sources
3
Reference mass
Ranges 0.015 – 0.024 kg across 2 sources
2
Where the figures differ, use the drawing from the manufacturer you buy from.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
8 mm
Mean diameter dm
(D + d) / 2
20 mm
C / C₀ load ratio (3 sources)
dynamic ÷ static load rating
RCL 2.16 · NBK 2.14 · INYOUNG 2.15
Arithmetic on the figures above — not a bearing life calculation for your load case.
CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.
Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs
72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
GOOT publishes miniature/small deep-groove and angular-contact bearings, including spindle and motor contexts. The metric table distinguishes open, ZZ and -2RS designations; confirm the current controlled specification and qualification instead of using older website content as a present delivery promise.
Published ranges: Deep groove ball bearings · Stainless steel and flanged variants · Angular contact ball bearings
6 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.
Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings
93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.
Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings
32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.
Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings
131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Global publishes ordinary shielded/sealed bearings alongside nonstandard steel and polymer pulley assemblies. Its scanned catalogue provides useful part-specific dimensions and construction examples; distinguish bore from shaft dimensions, match the complete assembly drawing, and confirm lubricant, noise testing and the current contracting entity.
Published ranges: Miniature and small bearings · Rubber-sealed bearing designs · Metal-shielded bearing designs
71 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Rendered PDF page 6, printed page 9, actual 6001 row and column headings examined: envelope, ratings, ball complement, mass and lubrication-specific speeds.
Current series description read. No readable 16001 parameter row found on the examined page, so historical directory speed and mass are not newly verified.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies