BearingIndex
THE BEARINGINDEX DIRECTORY

16016 — 80 × 125 × 14 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 14 mmD = 125 mmd = 80 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16016

16016 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 80 × 125 × 14 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
80 mm
Outside D
125 mm
Width B
14 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Moving from ZWZ 6016 to 16016 leaves an 8 mm axial design change.

The two ZWZ catalogue rows share an 80 mm bore and 125 mm outside diameter. Their widths differ: 16016 is 14 mm; 6016 is 22 mm. Matching the shaft and housing diameters does not preserve the axial locating stack or the allowable shoulder fillet.

Same seat diameters; different width and corner requirements.

ZWZ’s actual part-number results [1] list these dimensions for the exact 16016 and plain 6016 rows. The nearby 6016M row is a separate designation and is not silently substituted.

ZWZ field, mm160166016Drawing consequence
Bore / outside diameter80 /12580 /125Nominal diameters match; this alone does not establish fits or interchangeability.
Width B1422The catalogue width difference is 8 mm.
Shaft shoulder da min85.687Check the actual shoulder, not merely the 80 mm shaft seat.
Housing shoulder Da max119.4118Check the actual ring support and adjacent components.
Mounting fillet ra max0.61.1An old fillet permitted by the 6016 row may exceed the 16016 bound.

For the nominal shoulder-diameter bounds alone, a drawing meeting da ≥ 87 mm and Da ≤ 118 mm also lies within the listed 16016 bounds. That does not clear the fillet: a specified radius above 0.6 mm still exceeds the 16016 mounting limit even if it was within the 6016 limit. Check the maximum radius including its drawing tolerance; do not substitute the old shoulder check for this new corner check.

An 8 mm width difference is not an 8 mm spacer instruction.

If one side of a ring remains against the same shoulder, its opposite side face moves by the 8 mm nominal width difference. The actual assembly may locate the inner and outer rings from different sides, so review each ring’s locating faces separately. Identify the shaft shoulder, nut or spacer that retains the inner ring, and the housing shoulder, cover or other feature that locates the outer ring.

SKF’s independent axial-location guidance [2] explains that an interference fit alone is typically insufficient for axial location and shows several retaining arrangements. It supports checking the load path, not prescribing a particular accessory for ZWZ 16016.

If the redesign must preserve an existing component’s axial position, dimension that position from its actual datum and redesign the relevant locating stack. If it deliberately uses the reduced width to shorten the assembly, update the shoulder and cover positions accordingly. In either case, check that clamping supports the intended ring, rotating and stationary parts remain clear, and any intended axial movement remains possible.

A loose 8 mm washer selected only from the width subtraction does not establish those conditions. A designed distance ring or another retaining change needs its own support faces, tolerances and assembly assessment. This page supplies neither a ready-made spacer drawing nor approval to machine an existing shaft fillet smaller.

The ZWZ geometry comparison does not revalidate the INYOUNG listing.

The directory currently lists one historical INYOUNG 16016 publication. Its source page displayed a maintenance notice during this review. Its recorded ratings, speeds and mass remain labelled historical; the new ZWZ shoulder dimensions are not assigned to INYOUNG’s bearing. Obtain the offered manufacturer’s controlled drawing before applying this comparison to a quotation.

ZWZ’s 16016 dynamic-rating cell literally ends with “32.”. This review does not guess a missing digit or use it for a life calculation. The ZWZ speed header also renders r with a subscript min rather than an unambiguous r/min unit. Its raw 5700/6700 entries are not promoted here to confirmed rpm operating limits.

After resolving the 14 mm installation, assess the actual load and lubrication with the selected manufacturer. The same nominal bore and outside diameter do not prove the thinner bearing has the former bearing’s load capability, rigidity or operating clearance. Release a revised assembly and a maker-specific bearing specification together; dimensional fit alone closes only part of the substitution decision.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
INYOUNG
16016
25.2
Historical INYOUNG record; its source currently shows a maintenance notice and was not reverified.
25.2
Historical INYOUNG record; not confirmed by the independent ZWZ catalogue comparison.
4800
Historical INYOUNG speed; the current maintenance page does not confirm the offered duty.
6000
Historical INYOUNG speed; no current operating approval established.
0.6
Historical INYOUNG reference mass; the separate ZWZ entry is not assigned to this record.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 222.5 mm
Mean diameter dm(D + d) / 2102.5 mm
C / C₀ load ratiodynamic ÷ static load ratingINYOUNG 1

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16016.

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16016

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
GeneratorsINYOUNG
MotorcyclesINYOUNG

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16016.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. INYOUNG · 16016 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZWZ · exact 16016 and 6016 catalogue rows ↗

    Independent part-number search and exact designation cells checked; actual rows/screenshots viewed. 80/125 mm common envelope diameters, 14 versus 22 mm widths and separate shoulder/fillet bounds. Literal 16016 Cr 32. and malformed speed-unit header are unresolved; no ZWZ fields assigned to INYOUNG.

  2. SKF · Rolling bearings 17000, axial location, printed page 178 ↗

    PDF page 180 read, rendered and actually viewed. Axial retaining arrangements and supporting load path used as general technical background, with no SKF accessory dimensions or numeric limits assigned to ZWZ.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.