BearingIndex
THE BEARINGINDEX DIRECTORY

16004 — 20 × 42 × 8 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 8 mmD = 42 mmd = 20 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16004

16004 is a deep groove ball designation documented on BearingIndex from 7 manufacturer publications. The published boundary dimensions are 20 × 42 × 8 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
20 mm
Outside D
42 mm
Width B
8 mm

Compare the 7 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Does a drawing marked only 20×42×8 mm define the seat for LYC 16004?

No. LYC also specifies a 22 mm minimum shaft-side shoulder diameter, 40 mm maximum housing-side shoulder dimension and 0.3 mm maximum mating corner radius. Keep those separate from the 20 mm bore and 42 mm outside diameter when reviewing the assembly drawing.

The seat diameters and the shoulders have different roles.

LYC’s actual 16004 row and mounting diagram [1] publish d = 20 mm, D = 42 mm and B = 8 mm. The adjoining diagram identifies da and Da on the mating shoulders, plus ra at the mating corners.

d = 20 mm; D = 42 mm
These are the bearing’s nominal bore and outside diameter. The selected shaft/housing fit requirements still need to be specified; the nominal numbers are not manufacturing tolerances.
da ≥ 22 mm; Da ≤ 40 mm
These are the published lower and upper bounds for the shoulder dimensions identified by LYC’s diagram. They are not substitutes for d and D.
ra ≤ 0.3 mm
This is the mating corner-radius bound. The boundary table separately gives bearing chamfer r minimum = 0.3 mm. Equal displayed numbers do not make the symbols or bound directions interchangeable.

Add the mating shoulder and corner dimensions to the actual drawing under their own symbols. Mark which ring each shoulder locates and which component retains it axially. The 8 mm bearing width alone does not describe that locating arrangement.

Three illustrative drawing errors can be found before an order is placed.

The following values are hypothetical drawing entries for a selected LYC 16004, not measurements from a tested assembly. Each is screened against the specific published bound above.

Illustrative entryLYC boundDrawing-review result
da = 21 mmMinimum 22 mmBelow the published shaft-side shoulder bound; return the shoulder design for review.
Da = 41 mmMaximum 40 mmAbove the published housing-side shoulder bound; resolve the locating geometry.
ra = 0.6 mmMaximum 0.3 mmExceeds the stated mating corner-radius limit; the bearing’s r minimum is not permission to use this radius.

These comparisons identify a mismatch with LYC’s catalogue bounds. They do not diagnose a running fault or authorize grinding the shaft, altering the housing or changing the radius on an existing machine. Resolve the selected drawing and its tolerances with the responsible designer and supplier.

A drawing that satisfies all three numerical bounds still needs the actual fits, clearance and axial retention checked. Passing this limited screen is not complete assembly acceptance.

A second 20/42/8 row does not inherit LYC’s mounting specification.

NBK’s current 16004 row [2] also gives 20/42/8 mm, but lists Cr/Cor = 8370/4520 N and grease/oil speeds of 16000/19000 rpm under non-contact headings. LYC’s examined row lists 6.91/3.97 kN and 17000/20000 r/min. Keep those complete rows with their manufacturers.

If buying NBK or another maker instead, request that maker’s mounting-dimension drawing and conditions for the offered full designation. Do not apply LYC’s 22/40/0.3 limits as a newly verified specification for every 16004 offer.

For the LYC item, the catalogue identifies present designation 16004 and original designation 7000104E. Retain that exact mapping and confirm the current revision when replacing an older item. The next useful deliverable is a selected bearing drawing checked against the assembly’s own shoulder, corner and locating dimensions.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Minimum corner radius (mm)Reference mass (kg)Source recorded
CZ
16004
——————2026-09-24 source ↗Request
Yuyao Global
16004
——————2026-09-24 source ↗Request
RCL
16004
7.924.4451800020000—0.0522026-09-24 source ↗Request
GOOT
16004
————0.3—2026-09-24 source ↗Request
NBK
16004
8.374.521600019000——2026-09-24 source ↗Request
INYOUNG
16004
7.94.451800020000—0.0482026-09-24 source ↗Request
LYC
16004
6.913.971700020000——2026-09-23 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingRanges 6.91 – 8.37 kN across 4 sources4
Static load ratingRanges 3.97 – 4.52 kN across 4 sources4
Limiting speed — greaseRanges 16000 – 18000 rpm across 4 sources4
Limiting speed — oilRanges 19000 – 20000 rpm across 4 sources4
Reference massRanges 0.048 – 0.052 kg across 2 sources2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 211 mm
Mean diameter dm(D + d) / 231 mm
C / C₀ load ratio (4 sources)dynamic ÷ static load ratingRCL 1.78 · NBK 1.85 · INYOUNG 1.78 · LYC 1.74

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16004.

CZ

Ningbo, Zhejiang, China

Miniature motor bearings and inch series

CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.

Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs

72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask CZ about 16004

GOOT

Ningbo, Zhejiang, China

Deep groove ball bearings and miniature variants

GOOT publishes miniature/small deep-groove and angular-contact bearings, including spindle and motor contexts. The metric table distinguishes open, ZZ and -2RS designations; confirm the current controlled specification and qualification instead of using older website content as a present delivery promise.

Published ranges: Deep groove ball bearings · Stainless steel and flanged variants · Angular contact ball bearings

6 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask GOOT about 16004

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16004

LYC

Ball and roller bearings

LYC publishes a broad bearing portfolio. This sourcing guide separates catalogue selection, engineered applications and order-specific evidence.

49 designations documented here · source recorded 2026-10-07

Ask LYC about 16004

NBK

Ningbo, Zhejiang, China

Deep groove ball bearings and custom variants

NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.

Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings

32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask NBK about 16004

RCL

Ningbo, Zhejiang, China

Thin-wall ball bearings for compact mechanisms

RCL publishes 67/68/69, MR and 16 thin-section families and a harmonic-reducer bearing page. Its 67-series description explicitly asks designers to consider load capacity; encoder and flexible-bearing applications need different qualification inputs.

Published ranges: 67- and 68-series thin-wall bearings · 69-series ball bearings · 60-series ball bearings

131 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask RCL about 16004

Yuyao Global

Ningbo, Zhejiang, China

Miniature and small bearings

Global publishes ordinary shielded/sealed bearings alongside nonstandard steel and polymer pulley assemblies. Its scanned catalogue provides useful part-specific dimensions and construction examples; distinguish bore from shaft dimensions, match the complete assembly drawing, and confirm lubricant, noise testing and the current contracting entity.

Published ranges: Miniature and small bearings · Rubber-sealed bearing designs · Metal-shielded bearing designs

71 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Yuyao Global about 16004

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
Automotive systemsYuyao Global
BicyclesRCL
Brushless motorsCZ
Circular loomsRCL
Communications equipmentYuyao Global
Dental equipmentGOOT
DronesCZ
Encoders and motorsRCL
Garden toolsCZ
GeneratorsINYOUNG
Household appliancesYuyao Global
Medical equipmentYuyao Global
MotorcyclesINYOUNG
Office equipmentGOOT
Power toolsCZ, GOOT
Precision motorsGOOT
RoboticsRCL

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16004.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. CZ · 16004 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. Yuyao Global · 16004 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  3. RCL · 16004 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  4. GOOT · 16004 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  5. NBK · 16004 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  6. INYOUNG · 16004 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  7. LYC · 16004 source ↗

    Directory record dated 2026-09-23. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. LYC · exact 16004 dimensional and mounting row ↗

    PDF page 54, printed pages 101–102, actual first row of the 20 mm group aligned across both rendered halves. Boundary dimensions, shoulder/corner bounds, ratings, speed columns and present/original designation read.

  2. NBK · exact 16004 row ↗

    Current row and mm/N/rpm headers read; both speed headings non-contact. Does not provide LYC’s mounting bounds or transfer construction approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.