BearingIndex
THE BEARINGINDEX DIRECTORY

16009 — 45 × 75 × 10 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 10 mmD = 75 mmd = 45 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16009

16009 is a deep groove ball designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 45 × 75 × 10 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
45 mm
Outside D
75 mm
Width B
10 mm

Compare the 2 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Which 16009 rating applies to the bearing actually offered?

NBK publishes 15.6 / 12.2 kN dynamic/static ratings; CZ’s examined image row publishes 12.91 / 10.47 kN. Both show 45/75/10 mm. A shared designation and envelope do not make the two sets of ratings interchangeable.

The maker with the higher load rating has the lower listed speeds here.

The specific NBK detail [1] and CZ’s actual 16009 image row [2] give the following independent published entries. Source loads in newtons have been converted to kilonewtons.

Examined sourceCr / CorGrease / oil speed
NBK · brand ZHY15.6 / 12.2 kN8200 / 10000 rpm
CZ12.91 / 10.47 kN9200 / 11000 rpm

Do not combine NBK’s higher Cr with CZ’s higher speed to create a third specification. Identify the manufacturer on the quotation and keep its own ratings, lubrication basis and offered construction together. Neither source provides a tested operating point combining its largest listed load and speed.

NBK’s specific page allows steel or ceramic balls, customizable closure and precision options. Those choices are not a declared delivered configuration. CZ’s series image also shows multiple closure designs without selecting one for a particular order. Obtain the complete offered designation before applying the source figures.

Cor is not the load you can assign directly to a stationary machine.

If this bearing carries a load while stopped, during a slow movement or at a peak event, the static review needs the actual bearing load cases. The published 12.2 kN NBK and 10.47 kN CZ values are basic static ratings; neither is an application-specific allowable load.

SKF’s general load-selection explanation [3] converts combined radial and axial forces into an equivalent static bearing load P₀ using bearing-dependent factors. It calls for the maximum load combination that can occur. The factors and required criterion for the offered NBK or CZ construction must come from that manufacturer; this page does not substitute SKF product factors.

Give the supplier the radial and axial forces that occur together at this bearing, including the relevant peak or shock cases. State the support arrangement and whether permanent deformation would be acceptable for the required running performance. Ask for the calculation basis, resulting P₀ and the required static safety factor, with the offered Cor explicitly identified.

The shared Cr/Cor arithmetic below is not that static safety factor. A static assessment compares the relevant static rating with an equivalent applied load and the required criterion. A ratio between two catalogue ratings contains no actual machine load and cannot demonstrate that the stationary case passes.

There is no supplied machine load set for this page, so no pass/fail or safe working load is reported. For rotating duty, request the separate life and lubrication assessment as well; a completed static review does not establish service life at the listed speeds.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
CZ
16009
12.91
CZ’s exact 16009 image row gives 12910 N, shown here as 12.91 kN. This independently checked CZ rating is not NBK’s value.
10.47
CZ’s exact row gives 10470 N, shown here as 10.47 kN. This is a basic static rating, not a machine working-load allowance.
9200110000.1712026-09-24 source ↗Request
NBK
16009
15.612.2820010000—2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Dynamic load ratingRanges 12.91 – 15.6 kN across 2 sources2
Static load ratingRanges 10.47 – 12.2 kN across 2 sources2
Limiting speed — greaseRanges 8200 – 9200 rpm across 2 sources2
Limiting speed — oilRanges 10000 – 11000 rpm across 2 sources2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 215 mm
Mean diameter dm(D + d) / 260 mm
C / C₀ load ratio (2 sources)dynamic ÷ static load ratingCZ 1.23 · NBK 1.28

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16009.

CZ

Ningbo, Zhejiang, China

Miniature motor bearings and inch series

CZ publishes more than a series list: endurance examples, seal/torque comparisons, thermal considerations and Ppk/Cpk targets. Use those details to define the trial for your motor, keeping a 6205ZZ fatigue example separate from the unnamed high-speed endurance test and requesting current part-linked reports and certificate scope.

Published ranges: Metric miniature motor bearings · Inch R-series bearings · Stainless steel bearings · Nonstandard bearing designs

72 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask CZ about 16009

NBK

Ningbo, Zhejiang, China

Deep groove ball bearings and custom variants

NBK’s actual 5200 and Q523 pages separate dimensions, tolerance fields, steel/Si3N4 ball options and grease/oil speeds. Its ceramic route is a steel-ring hybrid proposal, not an all-ceramic corrosion or temperature guarantee. Reconcile actual in-house/outsourced manufacturing with the offered order; ISO9001 and ISO14001 queried valid on2026-10-08, while the displayed IATF image expired in2025 and requires a current record.

Published ranges: Deep groove ball bearings · Customer-specific nonstandard bearings

32 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask NBK about 16009

Applications the publishing works state.

ApplicationStated by
Brushless motorsCZ
DronesCZ
Garden toolsCZ
Power toolsCZ

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1
1601680 × 125 × 14Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16009.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. CZ · 16009 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. NBK · 16009 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. NBK · exact 16009 specification page ↗

    Fresh detail loaded and read: ZHY brand, 45/75/10 mm,15600/12200 N and8200/10000 rpm, with customizable closure/material/precision choices. No selected batch or machine assessment inspected.

  2. CZ · actual 16000-series image, 16009 row ↗

    Fresh source image opened and desktop screenshot actually viewed: exact16009 row12910/10470 N,9200/11000 rpm,0.171 kg and45/75/10 mm. Previously missing site-record fields individually supplemented; no neighbouring-row values transferred.

  3. SKF · Rolling bearings17000, equivalent static load, printed page105 ↗

    PDF page107 read, rendered and actually viewed. General combined-load and maximum-combination principle only; no SKF product factor, safety-factor threshold or rated capacity transferred to NBK or CZ.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.