Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller
21304CTN1
21304CTN1 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 20 × 52 × 15 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
What actually changes in a ZYS 21304CA-to-21304CTN1 quotation?
The nominal dimensions stay 20/52/15 mm. ZYS’s CTN1 row has higher basic load ratings and a lower listed mass, but the two rows have the same grease and oil speed entries. The quotation still needs to identify the supplied cage and its operating conditions.
Higher ratings in this row do not come with higher listed speeds.
ZYS’s actual adjacent rows [1] allow a specific catalogue comparison. These figures belong to this manufacturer, not every supplier using the designations.
Published field
21304CA
21304CTN1
d / D / B
20 / 52 / 15 mm
20 / 52 / 15 mm
Cr
31.7 kN
35.8 kN
Cor
32.1 kN
35.2 kN
Grease / oil limiting speed
6000 / 7500 rpm
6000 / 7500 rpm
Reference mass
0.175 kg
0.161 kg
The CTN1 entries are 4.1 kN higher for Cr and 3.1 kN higher for Cor; its listed mass is 14 g lower. Those are source-field differences. They do not demonstrate a higher allowable machine load, a measured service-life gain, lower running temperature or a higher speed. The speed columns themselves show no increase.
For a meaningful replacement comparison, give ZYS the same radial/axial load cases, rotational duty, alignment, fits and lubrication for both options. Request the resulting selection assessment for each complete offered designation. Comparing a CA offer under one duty assumption with a CTN1 offer under another does not establish which solves your machine’s problem.
“Nylon” is not a complete material or temperature specification.
ZYS’s TN1 series description names a nylon-shaped cage guided by the rollers. It does not identify a resin grade, reinforcement, thermal limits or compatibility with the lubricant in your machine. Treat that description as a reason to verify the offered construction, not as permission to fill in “PA66” or import another maker’s temperature range.
Include the lubricant’s exact product and additives, the expected bearing operating temperature and temporary temperature excursions in the replacement request. Ask ZYS to state the supplied cage material and the approved conditions for that combination. A generic “suitable for heavy load” response leaves these particular questions unanswered.
The CA comparison must be equally specific. The examined CACM series text says solid cage but does not establish that this offered 21304CA has a brass cage. The useful procurement record is the declared construction of each offer, its limitations and the same-duty assessment—not an assumed metal-versus-polymer comparison.
Keep the bore distinction in the purchase order: the table pairs cylindrical 21304CTN1 with tapered 21304KCTN1. Preserve that exact K position when checking a quotation. The table does not approve a tapered item for the existing cylindrical seat. For the shared da / Da / ra boundaries and the source’s conflicting axial-load prose, use the 21304CA mounting review; matching those boundaries is only one part of replacement approval.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
16 mm
Mean diameter dm
(D + d) / 2
36 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.
87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 20x52x15 mm envelope.
Fresh exact row and full units read in browser, with adjacent CA comparison. Series TN1 text names nylon and roller guidance; it does not establish a resin grade or an operating temperature/lubricant qualification for an offered batch. No measured life, speed-up or thermal result inspected.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies