Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller
21305CTN1
21305CTN1 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 25 × 62 × 17 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does the 6700 rpm entry apply to a grease-lubricated 21305CTN1 offer?
ZYS labels 6700 rpm under oil lubrication and 5300 rpm under grease. The higher entry does not document a grease-lubricated operating capability. A proposal to use oil also needs a defined system; the source row does not specify one.
Keep the speed figure attached to its source heading.
The selected grease and the actual grease-lubricated operating assessment.
Oil
6700 rpm
The selected oil and the lubrication system used for the assessed duty.
If an offer specifies grease but cites 6700 rpm from this table, ask the supplier to correct the basis or provide separate manufacturer evidence for that grease-lubricated duty. The oil column alone does not supply it. Operation below 5300 rpm is also not automatically approved: load, temperature, construction and lubrication still belong in the assessment.
The row gives Cr 45.5 kN and Cor 45.8 kN but does not combine those ratings with either speed entry into a tested operating point. Do not read the largest load and speed numbers as a simultaneous working condition.
Changing the lubricant name does not define an oil-lubricated installation.
The examined ZYS row says oil without specifying oil type, viscosity, supply method or quantity. It does not say that an oil bath, an external circulation system or a small feed line all support the same duty.
SKF’s general lubrication guidance [2] distinguishes oil-bath and circulating-oil arrangements. An oil bath retains oil in the housing; excessive level can increase temperature through churning. External circulation can remove heat and carry contamination toward filters, but its drainage must prevent oil accumulating around the bearing. These are design distinctions, not a selected system or an approved setting for ZYS 21305CTN1.
For a proposed conversion, send ZYS a housing section and a duty sheet that answer the following specific questions:
How does oil reach this bearing, and how is the required supply maintained during starting, running and stopping?
Where does it return or remain, and what prevents unintended accumulation or leakage?
Does the duty require heat removal or contaminant removal, and which equipment provides it?
Which exact oil product and operating temperature are included in the manufacturer’s assessment?
Request the assessed method and its required conditions together. This page does not prescribe a flow rate, oil level, viscosity grade or change interval because none is given for this ZYS item. A completed system drawing and manufacturer-defined conditions make the proposal reviewable; merely replacing grease with oil in the order does not.
Do not assume the designation includes a lubrication groove or qualified cage material.
ZYS describes W33 at series level as an outer-ring oil groove with three oil holes. The examined designation is 21305CTN1, without W33. It does not establish whether the actual offered batch includes those features. Have the offered construction and drawing state the feed features explicitly rather than assuming a housing feed port matches them.
The TN1 series description names nylon but does not identify a resin grade or oil/temperature qualification. Include the selected lubricant when requesting cage compatibility. The TN1 quotation review explains the material information that remains unconfirmed.
Preserve the bore variant as well: ZYS lists cylindrical 21305CTN1 and tapered 21305KCTN1. A lubrication proposal is not approval to substitute the tapered construction in the existing cylindrical seat. The actual 25/62/17 mm envelope and 32 / 55 / 1 mm mounting bounds remain drawing inputs, not a complete system design.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
18.5 mm
Mean diameter dm
(D + d) / 2
43.5 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.
87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 25x62x17 mm envelope.
Fresh exact row and all headings read in browser: grease/oil speed distinction, dimensions, ratings and bore variants. TN1 and W33 are series descriptions; no specific oil system or supplied-batch qualification inspected.
PDF page124 read, rendered and actually viewed. General oil-bath/circulation, heat-removal and drainage principles only; no SKF numerical oil setting, oil-change interval or operating approval transferred to ZYS.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies