BearingIndex
THE BEARINGINDEX DIRECTORY

21307CTN1 — 35 × 80 × 21 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 21 mmD = 80 mmd = 35 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller

21307CTN1

21307CTN1 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 35 × 80 × 21 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
35 mm
Outside D
80 mm
Width B
21 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The higher ZYS 21307CTN1 ratings do not answer whether it suits a lightly loaded running duty.

The exact ZYS row gives 74.4 kN Cr and 77.7 kN Cor in a 35/80/21 mm envelope. Those catalogue ratings are not a minimum-load assessment. If the bearing size is chosen to fit the shaft or housing, check the actual lightest running conditions as well as the highest loads.

Cr and Cor are not a lower operating-load boundary.

ZYS’s exact 21307CTN1 row [1] gives Cr 74.4 kN, Cor 77.7 kN and grease/oil limiting speeds of 4000/5300 rpm. The adjacent 21307CA row gives 65.4/75.4 kN with the same speed entries. The CTN1 figures are higher, but the table gives no minimum load for either offered construction and no assessed idle-running condition.

SKF’s general size-selection guidance [2] explains why a bearing chosen for reasons such as shaft dimensions can be lightly loaded relative to its capacity. Very light loading can involve skidding, raceway smearing or cage damage rather than only fatigue; rapid acceleration and repeated starts/stops make minimum-load review particularly relevant. This is a technical reason to request ZYS’s criteria, not evidence that this ZYS item has suffered any of those failures.

Do not turn SKF’s general load fraction into a ZYS acceptance number. Its more specific spherical-roller discussion gives different expressions and lubrication/speed inputs [3]. That reinforces the need for a maker- and construction-specific requirement. No minimum force is calculated here from the 74.4 or 77.7 kN ratings.

The production load alone can omit the condition that needs review.

If these modes exist in your machine, give ZYS their bearing-level reaction loads and speed/time behaviour separately. They are possible duty modes to check, not reported operating conditions for a real machine on this page.

Duty mode to includeInformation neededQuestion for the assessment
Normal productionRadial/axial reactions at this bearing, speed range, duration and lubrication conditions.Does the full operating range meet the maker’s load, speed and lubrication requirements?
Idle or unloaded runningRemaining reactions when process load is removed, actual running speed and time spent in this mode.Are the minimum-load requirements met without assuming the normal production force remains?
Starts, stops and rapid speed changesAcceleration/deceleration profile and frequency, loads during the transition and lubricant state.Do the transient conditions require a different operating or lubrication arrangement?

Use the reactions at this bearing, not only the machine’s total payload or motor rating. Have the responsible designer establish the load path and which forces remain in each mode. A single maximum-force figure cannot describe a lightly loaded period.

Ask ZYS to return the applicable minimum-load requirement and the inputs behind it for the complete offered construction. If a requirement is not met, request a reviewed response—such as a change to bearing selection, lubrication or operating procedure—rather than assuming a higher-rated CTN1 is the remedy. Do not add preload simply to satisfy an estimated fraction; that would introduce its own clearance, heat and life assessment.

Minimum-load review supplements the maximum-load review.

Keep the maker’s minimum-load answer beside the running-life and peak/static-load assessments; it does not replace them. State which modes were included, the complete part and lubricant, required conditions and any unresolved inputs. A reply saying only that the actual load is below Cr does not answer the light-load question.

The CTN1 series description names a nylon cage but does not specify this offer’s resin grade or lubricant/temperature qualification. Include those choices with the duty sheet. The exact row’s reference mass is 0.507 kg; that is a part-mass entry, not the bearing reaction force or a minimum-load value.

The source also distinguishes cylindrical 21307CTN1 from tapered 21307KCTN1. Confirm the offered bore and clearance before releasing an assessment. For the mounting bounds of 44/71/1.5 mm and handling/measurement context, use the 21307 assembly review. The series introduction’s contradictory axial-load prose remains a question for ZYS rather than an operating approval.

What each manufacturer published.

ManufacturerSource recorded
ZYS
21307CTN1
2026-09-22 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 222.5 mm
Mean diameter dm(D + d) / 257.5 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 21307CTN1.

ZYS

Precision and special bearings

ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.

87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask ZYS about 21307CTN1

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 35x80x21 mm envelope.

DesignationBearing familyWorks
21307CASpherical roller1
30307Tapered roller1
6307-2RZDeep groove ball1
6307T1XDeep groove ball1
6307ZZ/2RSDeep groove ball1
760307-TNAngular contact1
S6307ZZ/2RSDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
21304CA20 × 52 × 15Spherical roller1
21304CTN120 × 52 × 15Spherical roller1
21305CA25 × 62 × 17Spherical roller1
21305CTN125 × 62 × 17Spherical roller1
21306CA30 × 72 × 19Spherical roller1
21306CTN130 × 72 × 19Spherical roller1
21307CA35 × 80 × 21Spherical roller1
21308CA40 × 90 × 23Spherical roller1
21308CC40 × 90 × 23Spherical roller1

Each envelope shown is that designation’s own published size.

Request a quote for 21307CTN1.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. ZYS · 21307CTN1 source ↗

    Directory record dated 2026-09-22. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZYS · exact 21307CTN1 and 21307CA rows ↗

    Both exact rows and headings read live, centred screenshot actually viewed: dimensions, ratings, lubrication-labelled limiting speeds, mass and bore variants. No model-specific minimum-load requirement or complete cage qualification found in examined material.

  2. SKF · requisite minimum load, printed page 106 ↗

    PDF index107 newly read, rendered and actually viewed. Technical background on very-light-load failure mechanisms and acceleration/starts/stops; SKF general fractions, speed thresholds and branded remedies not assigned to ZYS.

  3. SKF · spherical-roller load expressions, printed page 784 ↗

    PDF index785 read and rendered image actually viewed. Shows construction-specific minimum-load guidance with oil and reference-speed inputs; no numerical expression or SKF axial-load allowance used as a ZYS criterion.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.