BearingIndex
THE BEARINGINDEX DIRECTORY

21305CA — 25 × 62 × 17 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 17 mmD = 62 mmd = 25 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller

21305CA

21305CA is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 25 × 62 × 17 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
25 mm
Outside D
62 mm
Width B
17 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Can ZYS 21305CA use the existing 22205CA housing and locating stack?

The same 25 mm bore leaves two important interfaces different: ZYS lists a 62 mm outside diameter and 17 mm width for 21305CA, against 52 mm and 18 mm for 22205CA. The source does not support a direct replacement in an unchanged assembly.

The housing diameter and axial locating stack both need review.

The two actual ZYS rows [1] describe different nominal envelopes even though both begin with a 25 mm bore.

InterfaceZYS 22205CAZYS 21305CA
Bore d25 mm25 mm
Outside diameter D52 mm62 mm
Width B18 mm17 mm
da min / Da max / ra max30 / 46 / 1 mm32 / 55 / 1 mm

A housing seat designed for a 52 mm bearing outside diameter is not the specified seat for this 62 mm item. The 10 mm nominal difference is not a machining instruction: any proposed housing change also needs its wall section, fit, shoulder support, seals and neighbouring-part clearances reviewed.

The bearing is also 1 mm narrower. Trace the ring-locating contacts in the actual section—shaft shoulder, locknut or distance ring, housing shoulder and end cover as applicable. The source gives no existing machine stack, so this page cannot say which ring would move or what gap would result. Do not assume the old locking position or a 1 mm washer restores the original arrangement.

SKF’s general axial-location guidance [2] explains that an interference fit alone typically does not locate a ring axially and that the locating arrangement must carry the applied axial loads. Use that principle to review the assembly; retain ZYS’s specific 32 / 55 / 1 mm mounting bounds and obtain its controlled section. These bounds do not, on their own, specify fits or a complete locating design.

The larger outside diameter is not a speed upgrade in this table.

ZYS lists grease/oil limiting speeds of 5300 / 6700 rpm for 21305CA, compared with 8000 / 10000 rpm for 22205CA. A replacement review must use the new item’s entries. The catalogue does not support retaining the old item’s speed figures simply because the shaft bore is unchanged.

The 21305CA basic ratings are Cr 42.7 kN and Cor 45.5 kN, against 40 and 42 kN in the 22205CA row. Those higher ratings do not cancel the speed difference or approve your operating combination. Request ZYS’s assessment using the actual force cases, lubricant, operating temperature, alignment and speed history together.

Identify the bore construction before releasing the revised drawing. The source pairs cylindrical 21305CA with tapered 21305CAK; a K quotation introduces another interface change. For the distinction between bearing chamfer and machine fillet, and the conflicting axial-load statements in the series introduction, refer to the ZYS mounting and source-conflict review. Neither an assumed cage material nor an unlisted clearance class should be used to complete this replacement specification.

What each manufacturer published.

ManufacturerSource recorded
ZYS
21305CA
2026-09-22 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 218.5 mm
Mean diameter dm(D + d) / 243.5 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 21305CA.

ZYS

Precision and special bearings

ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.

87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask ZYS about 21305CA

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 25x62x17 mm envelope.

DesignationBearing familyWorks
21305CTN1Spherical roller1
30305Tapered roller1
6305-2RZDeep groove ball1
6305T1XDeep groove ball1
6305ZZ/2RSDeep groove ball1
760305-TNAngular contact1
S6305ZZ/2RSDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
21304CA20 × 52 × 15Spherical roller1
21304CTN120 × 52 × 15Spherical roller1
21305CTN125 × 62 × 17Spherical roller1
21306CA30 × 72 × 19Spherical roller1
21306CTN130 × 72 × 19Spherical roller1
21307CA35 × 80 × 21Spherical roller1
21307CTN135 × 80 × 21Spherical roller1
21308CA40 × 90 × 23Spherical roller1
21308CC40 × 90 × 23Spherical roller1

Each envelope shown is that designation’s own published size.

Request a quote for 21305CA.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. ZYS · 21305CA source ↗

    Directory record dated 2026-09-22. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZYS · actual 21305CA and 22205CA rows ↗

    Both independent rows and full headings freshly read in browser: nominal dimensions, mounting bounds, basic ratings, grease/oil speeds and cylindrical/tapered columns. No existing machine drawing or replacement test supplied.

  2. SKF · Rolling bearings 17000, axial location, printed page 178 ↗

    PDF page 180 read, rendered and actually viewed. General axial-location principle only; no SKF fit, accessory or machine modification approval transferred to ZYS.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.