Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller
21308CC
21308CC is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 40 × 90 × 23 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
A speed found for an NSK 21308 execution is not a speed limit for ZYS 21308CC.
ZYS’s actual 21308CC entry is 40/90/23 mm with grease/oil limiting speeds of 3600/4500 rpm. A comparison of another maker’s 21308 data must retain its complete designation and speed heading. NSK’s official table demonstrates why collecting the largest number under “speed” produces a misleading substitution claim.
Two lubricant columns and four speed categories are not the same data structure.
ZYS’s exact 21308CC row [1] has limiting-speed columns headed Grease and Oil. NSK’s official industrial-machinery catalogue [2] separately lists cylindrical 21308EAE4 and tapered 21308EAKE4 in a 40/90/23 mm row, with four speed categories. The NSK row is a separate manufacturer's construction, not another source for the ZYS part.
Source and exact execution
Grease limit
Oil limit
Additional speed categories
ZYS 21308CC
3600 rpm
4500 rpm; heading says Oil without identifying a system.
No separate thermal or forced-circulation mechanical entry in this examined row.
Here min⁻¹ denotes revolutions per minute in the bearing table. The unit comparison is straightforward; the conditions are not interchangeable. In particular, the NSK 11000 entry is not its grease or oil-bath limit, and none of the NSK entries changes the ZYS 3600/4500 figures.
NSK’s live 21308EAKE4 detail [3] explicitly attaches its mechanical value to properly designed and controlled forced-circulation oil lubrication. Its thermal oil-bath rating refers to ISO 15312 conditions. This page checked that explanation on the tapered NSK detail, not on a ZYS test report, and did not review every clause of the standard.
An equivalent-size search should return separate candidates, not a blended specification.
If a supplier proposes a cross-brand replacement, have it identify the maker and complete designation before comparing conditions. NSK’s catalogue distinguishes its cylindrical EAE4 and tapered EAKE4; ZYS separately lists cylindrical 21308CC and tapered 21308CCK. Keeping those differences explicit prevents a nominal 40 mm bore from concealing a changed seat or sleeve arrangement.
Ask each maker to assess the same load, rotational duty, temperature and actual lubricant system for its own complete item. For a proposed oil system, state whether the arrangement is a bath or a controlled external supply/return system and provide the relevant housing section. A quotation that says only “oil lubricated” does not identify whether it matches a cited forced-circulation basis.
Compare the complete drawings and requirements as well as the three boundary dimensions: shoulder support, fits, clearance, cage, retention and lubricant delivery. The original ZYS row gives da min 49 mm, Da max 81 mm and ra max 1.5 mm. Those values remain ZYS inputs; additional NSK bounds or material choices are not silently assigned to the ZYS offer.
ZYS lists Cr 88.8 kN and Cor 99 kN for 21308CC. Keep its loading assessment separate from any NSK capacity calculation rather than combining one maker’s rating with the other maker’s speed or calculation factors. No cross-brand replacement or simultaneous maximum-load/maximum-speed operation has been approved here.
For the actual equal CA/CC table entries and the internal-construction questions that remain, see the ZYS CA-versus-CC review. This cross-brand comparison adds the speed-definition problem; it is not a ranking of supplier quality, a service-life test or proof that the nominal envelopes alone make these bearings interchangeable.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
25 mm
Mean diameter dm
(D + d) / 2
65 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.
87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 40x90x23 mm envelope.
Exact row, bore columns and header units freshly read; centred source screenshot actually viewed. 40/90/23 mm, Cr88.8/Cor99 kN, grease/oil3600/4500 rpm and mounting49/81/1.5 mm. No thermal or forced-circulation column added to the source.
Official 185-page PartC downloaded; exact row text read and PDF index133 spread rendered and actually viewed. EAE4 cylindrical versus EAKE4 tapered and four distinct speed headings preserved. No catalogue edition date, stock or replacement approval inferred.
Complete live specification text read and speed-area screenshot actually viewed. Confirms oil-bath/forced-circulation speed definitions and K tapered bore. Its properties and adapters remain this NSK item’s, not the ZYS offer’s. Login-restricted PDF was not claimed obtained.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies