Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller
21307CA
21307CA is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 35 × 80 × 21 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
If a 21307CA seems to have no clearance during vertical handling, check how its components are positioned first.
ZYS publishes the 35/80/21 mm envelope, but no supplied clearance class or assembly measurement procedure for its 21307CA row. General spherical-roller mounting guidance identifies a handling effect that can obscure clearance: rings and rollers can move axially out of their normal position, particularly in a vertical arrangement.
The published row cannot diagnose an apparent zero-clearance reading.
ZYS’s exact 21307CA row [1] lists a 35 mm bore, 80 mm outside diameter and 21 mm width. Its other entries are Cr 65.4 kN, Cor 75.4 kN, grease/oil limiting speeds 4000/5300 rpm and reference mass 0.542 kg. No internal-clearance class or measurement setup is specified in that row. Its solid-cage series description also does not declare the material of a particular offered CA cage.
An actual clearance reading needs its own context: whether the bearing is unmounted or seated, how the components are supported, their position, measurement method and relevant temperature conditions. A reading made during handling is not automatically the bearing’s specified unmounted clearance, and it is not proof of the operating clearance after both rings are fitted.
SKF’s spherical-roller mounting discussion [2] explains that rings and the roller complement can move axially from their normal positions during handling. In a vertical arrangement, downward movement can eliminate apparent clearance; subsequent fit-related ring expansion or contraction can then lead to preload. This identifies a possible measurement/assembly issue to investigate, not a diagnosis of a defective ZYS bearing or proof that it is acceptable.
Define component alignment and measurement before applying the fit.
SKF’s general advice is to mount horizontally where possible and rotate a ring to align the rollers. Where that is impractical, it describes using a handling tool or other support to keep the components centred [2]. Ask ZYS to specify the applicable handling and measurement procedure for its actual offered 21307CA before using a reading to accept or reject the part.
Identify the delivered construction. Confirm the complete cylindrical 21307CA designation and supplied clearance requirement. The same source separately lists tapered 21307CAK; its mounting procedure is a different question.
Record the reading conditions. Note assembly orientation, mounted/unmounted state, support and roller/ring alignment, method, instrument and temperature. If a reading is unexpected, have those conditions checked against the maker’s procedure before proceeding.
Review the actual fits and support. Include the shaft and housing drawings and their tolerance extremes, then obtain the expected clearance effects and acceptance criteria for that arrangement.
Retain the installation evidence. Record the readings required by the approved procedure and link them to the part and drawing revision. A freely turning bearing or a note saying “installed tightly” does not replace the specified clearance assessment.
The model’s mounting bounds are da min 44 mm, Da max 71 mm and ra max 1.5 mm. The bearing’s rs min entry is also 1.5 mm, but equal numbers do not make bearing chamfer and machine fillet the same feature. Review the controlled section, shoulder support and nearby-part space together. The alignment-space review explains why shoulder dimensions alone do not establish room for movement.
No vertical machine, clearance measurement, installation trial or preload failure has been observed for this page. The practical outcome is an agreed assembly and measurement record, followed by the manufacturer’s clearance assessment for the actual fit and duty. The catalogue’s load and speed figures do not supply those missing acceptance criteria; its conflicting series axial-load statements also require model-specific clarification.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
22.5 mm
Mean diameter dm
(D + d) / 2
57.5 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.
87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.
Ask the manufacturer for these when you enquire.
Other designations with the same 35x80x21 mm envelope.
Exact 21307CA and neighbouring CTN1 rows and full headings read live; centred row screenshot actually viewed. Specific dimensions, mounting bounds, ratings, speeds and mass retained. No clearance class, measurement procedure or supplied cage material found in the examined model row.
PDF index789 text read and image actually viewed. Axial component displacement, vertical handling, horizontal mounting/alignment and support guidance used as technical background only. No SKF temperature, fit or clearance setting transferred to ZYS; no real assembly diagnosed.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies