BearingIndex
THE BEARINGINDEX DIRECTORY

21306CA — 30 × 72 × 19 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 19 mmD = 72 mmd = 30 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical roller

21306CA

21306CA is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 30 × 72 × 19 mm. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
30 mm
Outside D
72 mm
Width B
19 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Self-aligning does not tell you how far ZYS 21306CA can tilt inside your housing.

ZYS lists the 30/72/19 mm bearing and its mounting bounds, but no model-specific permissible misalignment angle. A useful selection review needs to describe the motion relative to the outer ring and show space around the moving bearing parts, alongside the actual load and speed.

A fixed seat offset and a rotating shaft deflection are different assessment inputs.

ZYS’s exact 21306CA row [1] gives dimensions, loads and speeds, but no angle limit. Its introduction describes self-alignment at series level. Neither the model label nor that description establishes an acceptable angle for the assembled machine.

SKF’s spherical-roller guidance [2] distinguishes misalignment that stays in a constant position relative to the outer ring from misalignment whose position changes. The latter can create additional sliding and has more restrictive conditions. SKF’s example includes rotating shaft deflection from an imbalance. These are reasons to describe the movement precisely to ZYS; SKF’s numerical angles and load conditions are not assigned to this bearing.

Describe to ZYSInclude in the duty/drawing submissionWhy it changes the review
Seat alignment at assemblyShaft and housing axes, tolerance extremes and the resulting angle at this bearing.Nominally concentric drawings can hide manufacturing or assembly offsets.
Deflection during operationHow the angle and its direction vary with shaft rotation and operating loads.A changing orientation relative to the outer ring is not the same condition as a fixed offset.
Neighbouring constraintsEnd covers, seals, spacers and other nearby parts, with their available clearances.The complete arrangement can limit usable movement even when the bearing itself can accommodate it.

Ask ZYS to state the permitted conditions for its complete offered 21306CA, including the direction/time behaviour, load and speed basis. Do not copy another maker’s 213-series angle as an answer, or describe “compensates misalignment” as approval for an unspecified bent shaft or vibrating application.

The published shoulder bounds do not specify the clearance on both sides.

ZYS lists da min 37 mm, Da max 65 mm and ra max 1 mm; its separate bearing chamfer entry is rs min 1.1 mm. Keep the mounting limits attached to the correct shaft/housing geometry. These entries do not give the full space envelope required for alignment movement.

SKF’s arrangement guidance [3] shows free space on both sides to avoid interference between rotating bearing parts and stationary machine parts. It makes that space dependent on the actual misalignment and lubrication-space requirements. Its numerical sizing rule belongs to its own guidance and clearance data; this page does not turn it into a ZYS end-cover dimension.

Show the shoulder, end cover and any seal in the same section rather than reviewing each drawing independently. Have ZYS identify the needed moving-part envelope for the proposed angle and confirm that the surrounding geometry leaves it unobstructed. A shoulder that meets da/Da/ra can still leave an adjacent part too close; the source row alone does not settle that check.

The table puts 21306CA in the cylindrical-bore column and 21306CAK in the tapered-bore column. Identify which construction the drawing and quote use. Changing the bore construction introduces a separate mounting review; the shared nominal envelope is not permission to substitute it.

A useful reply qualifies the arrangement under the actual combined conditions.

The row’s Cr 57.5 kN, Cor 63.9 kN and grease/oil limiting speeds of 4500/6000 rpm are separate catalogue entries. They are not an operating point combining maximum load, maximum speed and misalignment. Send the actual force cases and rotational duty with the alignment description and request one assessment of that combination.

ZYS’s introduction also contains conflicting axial-load statements. A series-level sentence cannot resolve whether the particular radial/axial loading and alignment are suitable. The source-conflict review preserves that uncertainty; obtain the model-specific loading assessment instead of choosing the favourable sentence.

The reviewable deliverable is a coordinated section plus a stated operating assessment: complete bearing construction, allowed alignment behaviour, required surrounding space and conditions used for the load/speed evaluation. No actual machine drawing, permissible ZYS angle, clearance class or completed test was supplied for this page, so no installation is marked passed.

What each manufacturer published.

ManufacturerSource recorded
ZYS
21306CA
2026-09-22 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 221 mm
Mean diameter dm(D + d) / 251 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 21306CA.

ZYS

Precision and special bearings

ZYS publishes precision bearings, screw-support components and complete spindle units, alongside inspection and analysis services. Decide which product or laboratory deliverable is required, then agree its drawing, duty and acceptance records. Confirm the responsible supply or testing entity and the scope of any claimed standard or laboratory service.

87 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask ZYS about 21306CA

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 30x72x19 mm envelope.

DesignationBearing familyWorks
21306CTN1Spherical roller1
30306Tapered roller1
30306DTapered roller1
6306-2RZDeep groove ball1
6306T1XDeep groove ball1
6306ZZ/2RSDeep groove ball1
760306-TNAngular contact1
S6306ZZ/2RSDeep groove ball1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
21304CA20 × 52 × 15Spherical roller1
21304CTN120 × 52 × 15Spherical roller1
21305CA25 × 62 × 17Spherical roller1
21305CTN125 × 62 × 17Spherical roller1
21306CTN130 × 72 × 19Spherical roller1
21307CA35 × 80 × 21Spherical roller1
21307CTN135 × 80 × 21Spherical roller1
21308CA40 × 90 × 23Spherical roller1
21308CC40 × 90 × 23Spherical roller1

Each envelope shown is that designation’s own published size.

Request a quote for 21306CA.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. ZYS · 21306CA source ↗

    Directory record dated 2026-09-22. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZYS · exact 21306CA row and spherical-roller introduction ↗

    Exact row and header units read live; row screenshot actually viewed. 30/72/19 mm, mounting 37/65/1 mm, cylindrical/tapered variants and stated ratings/speeds. No numerical misalignment limit published in the examined row.

  2. SKF · spherical roller bearing data, printed page 781 ↗

    PDF index782 text read and newly rendered image actually viewed: fixed-versus-changing misalignment relative to the outer ring and dependence on arrangement. SKF numerical angle, load threshold, sealed-bearing angle and clearance classes are not transferred to ZYS.

  3. SKF · free space on both sides, printed page 786 ↗

    PDF index787 text read and rendered image actually viewed, including Fig15. General interference and lubrication-space considerations only; no numerical Ca dimension or SKF accessory specification assigned to this ZYS offer.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.