BearingIndex
THE BEARINGINDEX DIRECTORY

16017 — 85 × 130 × 14 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 14 mmD = 130 mmd = 85 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16017

16017 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 85 × 130 × 14 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
85 mm
Outside D
130 mm
Width B
14 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 16017 catalogue ratio below one does not mean a failed static safety check.

The historical INYOUNG row records Cr 25.8 kN and Cor 26.2 kN, producing the 0.98 dynamic/static ratio shown below. Its denominator is another catalogue rating, not your applied load. It cannot establish a static pass or fail, nor rank a supplier’s manufacturing quality.

The historical 0.98 is catalogue arithmetic, not load margin.

The recorded INYOUNG figures give 25.8 ÷ 26.2 ≈ 0.9847, rounded to 0.98 in the shared calculation. No operating force enters that division. Reversing or rounding the ratio cannot turn it into a safety assessment.

As an independently readable comparison, ZWZ’s exact 16017 row [1] lists Cr 31.6 kN and Cor 29.9 kN, with 85/130/14 mm boundary dimensions. Their rating ratio is approximately 1.06. Being on opposite sides of one does not make one bearing approved and the other defective: neither ratio contains the machine’s actual load.

The INYOUNG page currently displays a maintenance notice. Its figures therefore remain historical, while the ZWZ row is separately reviewed catalogue evidence. This comparison is not a current quotation, batch test or permission to assign ZWZ ratings to an INYOUNG order.

Running fatigue and peak-load deformation require different inputs.

SKF’s published explanations [2] distinguish the basic-life calculation using dynamic rating C and equivalent dynamic load P from the static safety calculation s₀ = C₀/P₀. C₀ is the static rating; P₀ is the equivalent static bearing load for the actual force combination. It is not the dynamic rating C.

Question for this 16017 dutyInputs to establishWhat the 0.98 cannot answer
Required life while runningConfirmed dynamic rating, equivalent running load, rotational speed and operating time; account for lubrication and contamination as appropriate.It supplies neither the running load nor the speed/time history.
Deformation during a high load or peakConfirmed static rating, radial/axial force combination producing the governing equivalent static load, and agreed deformation/safety criterion.It gives no maximum force combination or allowable deformation criterion.

Check forces at the bearing position, not merely total machine weight or motor power. Ask the designer for the reaction loads from the actual arrangement. Where loads vary, identify the relevant running duty for the life assessment and the governing peak combination for the static assessment. A brief peak still needs its static check even if average running load is modest.

For combined radial and axial forces, obtain the equivalent-load method and factors appropriate to the offered bearing. The catalogue Cor value is not a general axial-load allowance. This page has no machine-force data and reports no service-life hours or static safety result.

Review two conclusions attached to the same offered bearing.

Request the supplier or machine designer’s calculation with the complete 16017 execution and current rating source, then trace the running and peak-load inputs separately. The result should identify the intended life/reliability criterion and the static deformation criterion. A document containing only the two catalogue ratings and their quotient does not provide either conclusion.

If the result fails the selected criterion, revisit the actual load case, arrangement or bearing choice with the designer. If the load is uncertain, resolve or bound that uncertainty rather than choosing a larger catalogue ratio as a substitute. The numerical static criterion itself depends on the duty and acceptable deformation; no universal threshold is imposed here.

ZWZ’s independent 16017 row also gives da min 90.6 mm, Da max 124.4 mm and ra max 0.6 mm. Those are installation boundaries for that maker’s row, not proof that the load assessment has passed and not new mounting data for INYOUNG. Its speed heading has the same malformed r-with-subscript-min format; the raw 5300/6400 entries are not treated as confirmed rpm duty limits in this review.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
INYOUNG
16017
25.8
Historical INYOUNG figure; its current product page shows maintenance and was not reverified.
26.2
Historical INYOUNG figure; a dynamic/static catalogue ratio is not a static safety factor.
4500
Historical INYOUNG entry; current execution and operating basis not reverified.
5600
Historical INYOUNG entry; no current application approval established.
0.63
Historical INYOUNG reference mass, not the independent ZWZ catalogue mass.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 222.5 mm
Mean diameter dm(D + d) / 2107.5 mm
C / C₀ load ratiodynamic ÷ static load ratingINYOUNG 0.98

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16017.

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16017

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
GeneratorsINYOUNG
MotorcyclesINYOUNG

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16017.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. INYOUNG · 16017 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZWZ · exact 16017 catalogue row ↗

    Part-number search waited for the exact designation cell; row DOM and actual screenshot checked. 85/130/14 mm, Cr 31.6/Cor 29.9 kN and mounting dimensions independently documented. Malformed speed unit retained as unresolved; no new INYOUNG ratings or order approval.

  2. SKF · Rolling bearings 17000, printed pages 89,105–106 ↗

    PDF pages 91,107 and 108 read; rendered pages 91/108 actually viewed, page 107 previously rendered and viewed. Basic life, equivalent static load and static safety distinctions used as technical background, without assigning SKF bearing coefficients or criterion tables to an offered 16017.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.