BearingIndex
THE BEARINGINDEX DIRECTORY

16018 — 90 × 140 × 16 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 16 mmD = 140 mmd = 90 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16018

16018 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 90 × 140 × 16 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
90 mm
Outside D
140 mm
Width B
16 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A ZWZ 16018M offer should not be shortened to 16018.

Searching ZWZ’s catalogue for 16018 returned a 16018M row with 90/140/16 mm dimensions. The manufacturer’s own code explanation defines the cage suffix M as solid brass guided by the balls. Removing M from the quotation removes a construction requirement; the common dimensions do not restore it.

The search term and catalogue item are different strings.

ZWZ’s actual result [1] identifies 16018M, not plain 16018. The row gives 90 mm bore, 140 mm outside diameter and 16 mm width, with Cr 33.6 kN, Cor 33.4 kN and reference mass 0.990 kg. Its mounting values are da min 96.8 mm, Da max 133.2 mm and ra max 1 mm.

The historical INYOUNG row below is recorded as 16018 with the same boundary dimensions but 33.5/33.5 kN ratings and 0.85 kg mass. That page currently shows maintenance, so it is not newly verified. Neither the small rating difference nor the mass difference proves an equivalent cage, a defect or a supplier quality ranking.

A buyer seeking a replacement should preserve the original approved construction and compare it with the offered construction. If the original order merely says 16018 and does not identify the cage, recover its drawing or supplier specification before declaring the M offer equivalent. The plain designation is not evidence that the original used a stamped cage.

M, MA, MB and a clearance-range M are not interchangeable labels.

The same ZWZ code page explains several meanings. Read the complete designation and the relevant code group rather than searching a single letter.

ZWZ code contextManufacturer’s explanation, paraphrasedOrder implication
Cage suffix MSolid brass cage guided by the balls.Retain the specified cage material and guidance in the offered execution.
Cage suffix MASolid brass cage guided by the outer ring.A shared material does not make its guidance identical to M.
Cage suffix MBSolid brass cage guided by the inner ring.Do not accept MB as a spelling variation of M.
M within the stated clearance-range explanationThe middle portion of the original clearance range, in the code group described alongside CN and the clearance classes.This clearance meaning does not redefine the cage suffix on the 16018M row.

ZWZ also allows numbered variants after the cage M, such as M2, for changed designs or materials. If a supplier quotes such a variant, obtain its actual specification instead of dropping the digit. These are ZWZ’s meanings; another manufacturer’s similar letter requires its own code evidence.

The 16018M row does not select a C3/C4 clearance, precision class or special grease suffix. Do not infer those requirements from the brass cage. Specify any required clearance and lubricant independently and have the maker confirm the complete combined execution.

Approve the construction change before matching the delivery to it.

For a proposed substitute, ask the manufacturer to identify the cage construction and guidance, the complete designation and the duty assessment for that offer. Explain why the change is proposed—availability, an existing failure investigation or a design revision—so the assessment addresses the actual problem. “Brass is better” does not establish improved life, noise or speed for your arrangement.

Keep the approved full designation and drawing revision in the purchase order and receiving criteria. Compare the delivered marking and batch documents with that approval; obtain clarification if the marking is abbreviated. Where cage construction is not evident externally, a general product photo or boundary-dimension measurement cannot settle it. Ask for traceable construction documentation or an agreed inspection method.

ZWZ’s speed heading is malformed r with subscript min. Its raw 5100/6000 entries therefore are not presented here as newly confirmed rpm limits or proof that the M execution outperforms the historical INYOUNG record. This page documents a specific alternative designation; it does not merge 16018M into the existing 16018 record or approve a machine substitution.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
INYOUNG
16018
33.5
Historical INYOUNG 16018 rating; its current source is under maintenance. The separate ZWZ 16018M rating is not assigned to it.
33.5
Historical INYOUNG figure; not newly reverified or replaced by ZWZ’s suffixed designation.
4300
Historical INYOUNG speed; current complete execution not reverified.
5300
Historical INYOUNG speed; no current duty approval established.
0.85
Historical INYOUNG mass; the heavier independent ZWZ 16018M row describes another maker/execution.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 225 mm
Mean diameter dm(D + d) / 2115 mm
C / C₀ load ratiodynamic ÷ static load ratingINYOUNG 1

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16018.

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16018

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
GeneratorsINYOUNG
MotorcyclesINYOUNG

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16018.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. INYOUNG · 16018 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. ZWZ · 16018M exact result and code description ↗

    Actual 16018 search returned 16018M; exact item cell, row HTML and screenshot read. Code description loaded after its heading matched; full text saved, M/MA/MB cage definitions and clearance-context M actually viewed. No plain 16018 ZWZ row, delivered cage test or automatic interchangeability established.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.