BearingIndex
THE BEARINGINDEX DIRECTORY

16019 — 95 × 145 × 16 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 16 mmD = 145 mmd = 95 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16019

16019 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 95 × 145 × 16 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
95 mm
Outside D
145 mm
Width B
16 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Identical LYC catalogue rows do not explain the 16019/YB3 specification change.

LYC’s official catalogue lists both 16019 and 16019/YB3 at 95/145/16 mm, with the same displayed ratings, speeds, mounting dimensions and mass. Its suffix instructions nevertheless identify /YB as a specification alteration and require drawings or supplementary specifications to establish the actual change.

The table proves shared listed figures, not identical complete specifications.

LYC’s official catalogue, printed pages 109–110 [1], has separate rows for 16019 and 16019/YB3. Both give the following catalogue figures:

LYC table fieldShared valueWhat remains to establish
Boundary dimensions d/D/B95/145/16 mmThe controlled drawing and any changed specification beyond the nominal envelope.
Dynamic / static rating43.9 /42 kNThe current offered construction and suitability for the actual duty.
Grease / oil limiting speed4200 /5000 r/minActual lubrication and operating conditions; these are catalogue entries, not machine test results.
Mounting da min /Da max /ra max100 /140 /1 mmThe machine’s actual shoulder geometry and locating arrangement.
Reference mass0.816 kgNo batch weighing tolerance or specification equivalence is defined by the matching number.

The catalogue is an existing official document, not a newly issued quotation. Have LYC identify the current revision applicable to the offer. The table contains no description of the actual /YB3 change; none is invented here.

A legacy designation mapping and a specification alteration answer different questions.

In the same table, the plain 16019 row has 700119E in the Original designation column. The 16019/YB3 row has no original designation printed. The catalogue therefore supplies that specific legacy mapping for plain 16019; it does not explicitly map 700119E to the /YB3 variant.

LYC’s suffix section, printed page 9, explains /YB as an alteration of specifications. For Y combined with another letter or digit, it directs the reader to the design department’s product drawing or supplementary specification. The trailing 3 in /YB3 is not explained there as C3 clearance, a precision grade or a grease code. Preserve the whole /YB3 identifier and obtain its actual definition.

If a maintenance record says 700119E, first establish the manufacturer and the original complete bearing requirement. The LYC catalogue mapping can help reconcile an LYC record, but it cannot establish another maker’s code system or recover unrecorded machine-specific requirements. A seller replacing that line with 16019/YB3 still needs to identify the alteration and demonstrate that it preserves the approved requirement.

Compare the actual altered requirement before releasing a substitute.

Request the document number and revision defining LYC 16019/YB3, the altered requirement and its acceptance method. Compare that requirement with the original approved bearing specification, not just the five shared catalogue fields. Where the change affects a required machine characteristic, have the supplier and designer confirm its effect on that requirement.

If the original requirement cannot be recovered, use the machine drawing, operating requirements and identifiable original part documents to establish a new approved specification. Do not describe that work as proof of automatic equivalence. If LYC’s defining supplement is unavailable, the /YB3 alteration remains unresolved even though both public rows look identical.

Carry the resulting full designation, defining document and approved revision into the purchase order and receiving criteria. A dimension check can verify the envelope; it cannot verify an unidentified altered specification. The required inspection or documentary evidence must address the particular change once LYC explains it.

The directory’s separate historical INYOUNG 16019 row records 37/36.8 kN, 4000/5000 rpm and 0.89 kg. Its current webpage shows maintenance. Those values are not replaced by LYC’s figures, and LYC’s /YB3 definition is not assigned to INYOUNG. This page documents the distinction for a replacement decision without claiming current stock or an approved substitution.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
INYOUNG
16019
37
Historical INYOUNG rating; current source page is under maintenance. The reviewed LYC catalogue values are separate manufacturer evidence.
36.8
Historical INYOUNG rating; not replaced or newly verified by the LYC catalogue comparison.
4000
Historical INYOUNG speed; LYC’s catalogue grease figure belongs to its own row.
5000
Historical INYOUNG speed; a matching number in another maker’s catalogue does not confirm this execution.
0.89
Historical INYOUNG mass; not the LYC reference mass or a receiving tolerance.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 225 mm
Mean diameter dm(D + d) / 2120 mm
C / C₀ load ratiodynamic ÷ static load ratingINYOUNG 1.01

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16019.

INYOUNG

Taizhou, Zhejiang, China

Ball and roller bearings from Wenling

INYOUNG publishes ball and roller bearing families from Wenling. Its deep-groove tables show why bore size alone is insufficient for replacement, while its material pages distinguish bearing-steel and stainless options. Obtain the current model drawing and confirm the offered material, closure and lubrication; online access limitations and catalogue inconsistencies remain unresolved.

Published ranges: Deep groove ball bearings · Cylindrical and tapered roller bearings · Spherical roller bearings · Angular contact bearings

93 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask INYOUNG about 16019

Applications the publishing works state.

ApplicationStated by
Air compressorsINYOUNG
GeneratorsINYOUNG
MotorcyclesINYOUNG

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16019.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. INYOUNG · 16019 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. LYC · official bearing catalogue, printed pages 9 and 109–110 ↗

    PDF pages 8 and 58 read, rendered and actually viewed. Exact 16019 and 16019/YB3 row alignment across the spread checked; original 700119E appears only on the plain row. /YB explanation and drawing/supplement requirement checked. Existing catalogue evidence, not a current quotation or the actual /YB3 defining supplement.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.