BearingIndex
THE BEARINGINDEX DIRECTORY

16100zz — 10 × 28 × 8 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 8 mmD = 28 mmd = 10 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16100zz

16100zz is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 10 × 28 × 8 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
10 mm
Outside D
28 mm
Width B
8 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A standard number in Hongchi’s 16100ZZ table is not a material or temperature test report.

Hongchi’s exact page gives a 10 mm bore, 28 mm outside diameter and 8 mm ZZ width. Its component table also has an inspection-standard column. Before using that column to qualify a purchase, check the intended standard, its subject and the evidence for the supplied bearing.

The official records do not turn these webpage cells into certificates.

Hongchi’s 16100zz table [1] places “GB-T 305-1998” next to the inner ring, outer ring, balls and ZZ shield entries, and “JB-T 8571-1997” next to grease and the −40 to 160 °C temperature entry. The following checks normalize that printed hyphen format to GB/T and JB/T. If the maker intended a different reference, obtain its corrected citation.

Printed referenceOfficial record checkedPurchasing consequence
GB-T 305-1998GB/T 305-1998 [2] concerns outer-ring snap-ring grooves and snap rings: dimensions and tolerances. The official platform marks it withdrawn and identifies GB/T 305-2019 as its replacement.This reference alone does not establish the composition or heat treatment of the listed GCr15 rings and balls, or the shield material.
JB-T 8571-1997JB/T 8571-1997 [3] is a sealed deep-groove-bearing test procedure addressing dust, grease leakage and temperature rise. Its official record marks it withdrawn.A test-method citation is not a passed report for this 16100ZZ and does not by itself substantiate the complete −40 to 160 °C operating claim.

These checks establish the official records’ titles and status, not the contents of every clause or a test performed by Hongchi. A withdrawn edition in an existing webpage also does not prove the delivered bearing is defective. Ask the supplier to reconcile the reference with the characteristic being offered and the current agreed specification.

Material identification and closure performance need different answers.

For a material requirement, identify the actual selected component first. The page names GCr15 for rings and balls, SPCC/SUS for ZZ shields, and SUS/MN for the cage; the slashed entries do not select the delivered alternative. Obtain the selected grades and the material/heat-treatment requirements in the controlled specification. Ask which report or certificate links those requirements to the supplied components.

A report evaluating a groove dimension cannot establish a steel grade merely because its standard number appears beside that grade. Equally, a material certificate cannot establish dust exclusion, grease leakage or temperature rise of the assembled bearing. Keep each required characteristic linked to its applicable requirement, method, result and acceptance limit.

If closure or thermal performance matters to the machine, request the report for the actual quoted 16100ZZ execution. Check its identity, lubricant, test conditions, measured results and stated criterion. An RS/RZ or open version sharing the same web page is not automatically the tested ZZ version. A general company certificate or a different-model report does not close that identity gap.

Specify the missing evidence rather than copying the standards column.

Ask Hongchi to return an evidence schedule for the offer: the complete part designation and revision; selected ring, ball, shield and cage materials; the characteristic each cited standard covers; the agreed edition and relevant requirement; and the report or agreed inspection that will verify it. Where an old edition remains contractually proposed, have the supplier and buyer resolve that choice explicitly instead of silently updating its number.

Keep the report number, specimen or batch identity and conclusion attached to the requirement it supports. If a type test is proposed rather than a batch test, define what that evidence qualifies and what receiving checks remain. No inspection has been performed for this page, and no missing certificate is described as a failed test.

The same source groups 16100zz/rs/rz/open and expressly calls its table reference information. It gives OPEN and ZZ widths of 8 mm, Cr 5110 N and Cor 2380 N. Those source readings do not resolve the standard-reference questions. The site’s historical supplier row below retains only boundary dimensions; the reviewed notes add the evidence needed to assess an offer without certifying the web table.

The nearby 6200 labels also need drawing-level reconciliation: Runstar’s exact 6200-2RS detail [4] lists 10/28/8, while Global’s 6200 catalogue row [5] lists 10/30/9 mm. This is a source discrepancy, not a correction inferred from the model name. Unconfirmed 6200-family matches have been omitted from this page’s same-envelope suggestions; obtain the actual maker’s complete drawing before considering a substitute.

What each manufacturer published.

ManufacturerSource recorded
Hongchi
16100zz
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 29 mm
Mean diameter dm(D + d) / 219 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16100zz.

Hongchi

Ningbo, Zhejiang, China

Miniature metric, inch and thrust bearings

Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.

Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings

80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Hongchi about 16100zz

Applications the publishing works state.

ApplicationStated by
Cooling fansHongchi
DronesHongchi
Miniature motorsHongchi
Precision instrumentsHongchi

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16100zz.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Hongchi · 16100zz source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Hongchi · 16100zz exact product table ↗

    Full model-page text and table HTML read; inspection-standard column screenshot actually viewed. Reference formatting, component options and mixed closure versions preserved; no test report or certificate obtained.

  2. National standards platform · GB/T 305-1998 ↗

    Official record read live and screenshot viewed: snap-ring/groove dimensions and tolerances, withdrawn 2020-05-01, replaced by GB/T 305-2019. Metadata and title checked; no claim to have read every standard clause.

  3. National standards platform · JB/T 8571-1997 ↗

    Official industry-standard record read live and screenshot viewed: sealed deep-groove-bearing dust, grease-leakage and temperature-rise test procedure; withdrawn status. No procedure limits or batch results inferred from metadata.

  4. Runstar · 6200-2RS exact detail ↗

    Actual detail read and screenshot viewed: 10/28/8 dimension entries; listing also gives the same envelope for 6200 and6200ZZ. No custom-design claim or guessed correction.

  5. Global · official catalogue, printed page 9 ↗

    PDF page 6 newly rendered and actually viewed: exact 6200 row 10/30/9 mm. Independent manufacturer comparison, not a Runstar drawing or an interchangeable-product approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.