BearingIndex
THE BEARINGINDEX DIRECTORY

16101zz — 12 × 30 × 8 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 8 mmD = 30 mmd = 12 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Deep groove ball

16101zz

16101zz is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 12 × 30 × 8 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
12 mm
Outside D
30 mm
Width B
8 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

16101ZZ and 6001ZZ share a 12 mm bore and 8 mm width. Their outside diameters still prevent a direct swap.

Hongchi’s two exact product pages give a useful comparison: 16101ZZ has a 30 mm outside diameter, whereas 6001ZZ has 28 mm. The larger outside diameter also comes with lower published dynamic and static ratings in these tables. Resolve the housing and load requirements independently.

A larger outside diameter does not establish a higher load rating.

The following values come from Hongchi’s 16101zz page [1] and its separate 6001zz page [2]. Each page groups ZZ, RS, RZ and open versions. The dimension rows explicitly give OPEN and ZZ widths; the load rows are not separately qualified by closure execution. Both tables say the data are for reference and ask buyers to consult the maker when selecting.

Published characteristic16101 page6001 pageWhat the comparison resolves
Bore / outside diameter / ZZ width12 / 30 / 8 mm12 / 28 / 8 mmBore and width match nominally; outside diameter differs by 2 mm.
Basic dynamic rating Cr4320 N5110 NThe 16101 table is 790 N lower. This is a subtraction of the published figures, not a measured performance difference.
Basic static rating Cor2250 N2380 NThe 16101 table is 130 N lower. A larger outside diameter does not justify carrying over the 6001 rating.

The tables do not explain the internal design responsible for these ratings. Do not infer ball size, ball count, raceway geometry or manufacturing quality from the outside diameter, and do not “correct” the maker’s numbers because the order seems unexpected. Obtain confirmed ratings for the complete offered part before calculating its suitability.

Check the outside-ring seat before discussing a replacement.

If an existing drawing specifies a housing seat for a nominal 30 mm outside diameter, a nominal 28 mm bearing does not reproduce that interface. The catalogue diameters differ by 2 mm, or 1 mm per side when centred. That is nominal arithmetic only: it is not the actual clearance of a measured assembly, because housing and bearing tolerances have not been supplied.

A sleeve or adhesive is not an approved remedy established by this comparison. Any proposed adapter changes the support and retention arrangement and needs its own controlled design, fits and approval. In the reverse direction, putting a nominal 30 mm outer ring into a seat specified for a nominal 28 mm bearing also requires an approved housing change; it is not a direct-fit substitution.

Matching the 12 mm bore and 8 mm width does not finish the interface review. Get the candidate’s actual shoulder and chamfer requirements and check the shaft and housing drawings against them. These two web tables do not publish enough mounting data to approve those details. Retain the required axial location and closure clearances in the replacement review rather than approving solely from the three boundary dimensions.

Decide why the design needs 16101ZZ, then qualify that execution.

For a design already requiring a 30 mm outer-ring seat, the published 16101ZZ envelope is the relevant starting point. Its 4320 N Cr and 2250 N Cor remain separate inputs needing maker confirmation and an application assessment. The 6001 page’s higher figures do not make its 28 mm outside diameter suitable for that seat.

For a new design considering both envelopes, compare the available housing arrangement and the required running and peak loads before choosing. Cr is not simply an allowable continuous applied load, and Cor is not a passed shock test. No service life or static safety result has been calculated here; neither bearing has been tested for a buyer’s machine. Confirm the exact execution and use the maker’s applicable calculation guidance with the actual duty and loading.

Ask for a reply that identifies: the complete offered 16101ZZ; its controlled drawing and mounting requirements; whether the grouped table’s ratings apply to that execution; and the selected clearance, lubricant and component materials. If the order is a substitution, attach the existing part and housing drawings and request an explicit comparison of the changed outer-ring interface and required duty. A quote repeating “12 mm bore, 8 mm width” leaves the decisive 30-versus-28 mm issue unanswered.

The historical supplier row below records Hongchi’s 12/30/8 mm dimensions. This reviewed comparison adds separately sourced information without assigning either maker table’s mixed-version ratings to that historical row, and without approving a substitute.

What each manufacturer published.

ManufacturerSource recorded
Hongchi
16101zz
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 29 mm
Mean diameter dm(D + d) / 221 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 16101zz.

Hongchi

Ningbo, Zhejiang, China

Miniature metric, inch and thrust bearings

Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.

Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings

80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Hongchi about 16101zz

Applications the publishing works state.

ApplicationStated by
Cooling fansHongchi
DronesHongchi
Miniature motorsHongchi
Precision instrumentsHongchi

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
1600112 × 28 × 7Deep groove ball6
1600215 × 32 × 8Deep groove ball6
16002E15 × 32 × 8Deep groove ball1
16002zz15 × 32 × 8Deep groove ball1
1600317 × 35 × 8Deep groove ball6
16003E17 × 35 × 8Deep groove ball1
1600420 × 42 × 8Deep groove ball7
1600525 × 47 × 8Deep groove ball5
1600630 × 55 × 9Deep groove ball5
16006zz30 × 55 × 9Deep groove ball1
1600735 × 62 × 9Deep groove ball2
1600840 × 68 × 9Deep groove ball3
16008zz40 × 68 × 9Deep groove ball1
1600945 × 75 × 10Deep groove ball2
1601050 × 80 × 10Deep groove ball3
16010ZZ/2RS—Deep groove ball1
1601155 × 90 × 11Deep groove ball2
16011zz55 × 90 × 11Deep groove ball1

Each envelope shown is that designation’s own published size.

Request a quote for 16101zz.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Hongchi · 16101zz source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Hongchi · 16101zz exact product page ↗

    Full page and both tables read; dimension and load screenshots actually viewed. 12/30/8 mm ZZ dimensions; grouped reference Cr 4320 and Cor 2250 N. No execution-specific drawing, calculation or test report obtained.

  2. Hongchi · 6001zz separate product page ↗

    Full separate page and tables read; dimension and load screenshots actually viewed. 12/28/8 mm ZZ dimensions; grouped reference Cr 5110 and Cor 2380 N. Comparison is limited to the published fields, not an interchangeable-part approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.